Bedienungsanleitung Roland D-05 (Seite 1 von 2) (Englisch)

710334

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

English

Owner’s ManualLINEAR SYNTHESIZER

D-05

In order to use this device correctly, please carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (the Leaet “USING THE UNIT SAFELY) before use.

After reading, keep these instructions at hand for immediate reference.

Introduction

The D-05 is a sound module that can be used in conjunction with the K-25m keyboard unit

(sold separately). The sound can be heard through the built-in speakers.

* The D-05 can operate on batteries or on USB bus power. If you are using batteries, insert four

AA batteries, making sure that the batteries are oriented correctly.

* If you handle batteries improperly, you risk explosion and fluid leakage. Make sure that

you carefully observe all of the items related to batteries that are listed in “USING THE UNIT

SAFELY” and “IMPORTANT NOTES” (leaflet “USING THE UNIT SAFELY”).

* When turning the unit over, be careful so as to protect the buttons and knobs from damage.

Also, handle the unit carefully; do not drop it.

* When the battery runs low, the display indicates “Battery Low.” Replace the battery as soon as

possible.

Using the D-05 in conjunction with the DK-01 Boutique Dock (sold separately)

For installation / removal / angle adjustment, refer to the DK-01’s Owner’s Manual.

Using the D-05 in conjunction with the K-25m keyboard unit (sold separately)

For installation / removal / angle adjustment, refer to the K-25m’s Owner’s Manual.

Playing the D-05 via MIDI or USB

You can also play the D-05 via MIDI or USB. For details, refer to “Connecting Your Equipment.”

Connecting Your Equipment

* To prevent malfunction and equipment failure, always turn down the volume, and turn off all

the units before making any connections.

A B C D E F

Micro USB ( ) port

Use a commercially available USB 2.0 cable (A-micro B)

to connect this port to your computer. It can be used to

transfer USB MIDI and USB audio data. You must install the

USB driver when connecting the D-05 to your computer. Download the USB driver from the

Roland website. For details, refer to Readme.htm which is included in the download.

https://www.roland.com/support/

* Do not use a micro USB cable that is designed only for charging a device. Charge-only cables

cannot transmit data.

[VOLUME] knob

Adjusts the volume.

PHONES jack

Connect headphones (sold separately) here.

OUTPUT jack

Connect this jack to your amp or monitor speakers.

MIX IN jack

This is the audio input jack. Sound from the connected device is output from the OUTPUT jack

and PHONES jack.

MIDI jack

You can play the D-05 by connecting a MIDI device via a

commercially available MIDI cable.

Turning the D-05 On

[POWER] switch

This turns the power on/o.

* After you’ve made connections correctly, be sure to turn on the power in the order of the

D-05 first, and then the connected system. Powering-on in the incorrect order may cause

malfunctions or damage. When turning the power off, power-off the connected system first,

and then the D-05.

* Before turning the unit on/off, always be sure to turn the volume down. Even with the volume

turned down, you might hear some sound when switching the unit on/off. However, this is

normal and does not indicate a malfunction.

* The D-05 automatically powers-off when a specified length of time has elapsed since it

was last played or operated (the Auto Off function). If you don’t want the power to turn off

automatically, disable the Auto Off function.

•

When the power is turned o, any settings you were editing will be lost. You must save

settings that you want to keep.

•

To restore power, turn the power on again.

Returning to the Factory Settings (Factory Reset)

Here’s how to return the D-05 to its factory-set state.

While holding down the PATCH BANK [2] button, turn on the power.

If you decide to cancel the factory reset, turn o the power.

Press the [ENTER] button to execute the factory reset.

When all buttons blink, turn the D-05’s power o, then on again.

Data Backup/Restore

Backup

Connect your computer to the D-05’s USB port via USB cable.

While holding down the [FUNCTION] button, turn on the power.

Open the “D-05” drive on your computer.

The backup les are located in the “BACKUP” folder of the “D-05” drive.

Copy the backup les into your computer.

After copying is completed, eject the USB drive.

Windows 10/8/7

Right-click on the “D-05” icon and execute “Eject.”

Mac OS

Drag the “D-05” icon to the Trash icon in the Dock.

Turn the D-05 power o.

Restore

As described in the procedure for “Backup” Step 1–3, open the “D-05” drive on your

computer.

Copy the D-05 backup les into the “RESTORE” folder of the “D-05” drive.

After copying is completed, eject the USB drive and then press the [ENTER] button.

After the LEDs have completely stopped blinking, turn o the power.

Panel Descriptions

1 2 3 4 6 7 8

5 9

Ribbon controller (C1/C2)

These are touch-type ribbon controllers. C1 (left) is pitch bend, and C2 (right) is modulation.

* If a K-25m keyboard unit, USB, or MIDI are not connected, touching the C1 controller plays a

preview sound.

Joystick

UPPER / LOWER / VALUE / LOCAL

These buttons switch the function of the joystick.

Indicator /

Button

Explanation

UPPER

The up/down direction changes the part balance, and the left/right direction

changes the partial balance of the selected part.

LOWER

VALUE Enters values, such as during editing.

LOCAL

Enables local editing (a function that lets you use the joystick to simultaneously

edit adjacent items in the display).

Select button Switches in the order of UPPER

LOWER VALUE LOCAL.

Display/ [ ] / [F1] / [F2] / [ ] buttons

From the left, these are indicated as [

] / [F1] / [F2] / [ ].

Enabled buttons (i.e., buttons that do something when pressed) are lit; disabled buttons are

unlit.

Use [ ] [ ] to switch pages. These are lit if an adjacent PAGE exists.

* Never strike or apply strong pressure to the display.

D-05MIDI keyboard

MIDI INMIDI OUT

[FUNCTION] [PRESET/USER] buttons

Button Explanation

FUNCTION Accesses the function menu screen.

PRESET/USER

Change the patch group.

Press this button, and then use [INCREMENT] [DECREMENT] to change.

Choose from P-1–6 and U-1–8.

After making the change, specify the patch bank and patch number to conrm.

[CHASE] [PORTAMENTO] [EDIT] [EXIT] buttons

Button Explanation

CHASE

Turns the Chase function on/o.

Chase is a function that sounds the upper tone when you press a key, and then

sounds a delayed note on the lower (or upper) part; it works when the key

mode is Whole or Dual. Depending on the patch, it can produce eects similar

to delay or sound-on-sound.

PORTAMENTO Turns the portamento function on/o.

EDIT Accesses the edit menu screen.

EXIT

Returns you to the previous screen.

In some screens, this button cancels the operation that’s being executed.

[SEQUENCER] [WRITE] [INCREMENT] [DECREMENT] buttons

Button Explanation

SEQUENCER

Accesses the sequencer screen.

Hold down the [SHIFT] button and press the [SEQUENCER] button to access the

arpeggiator screen.

WRITE Saves the sound or sequencer settings.

INCREMENT

Used to increment or decrement the value.

DECREMENT

Ten keys/ [SHIFT] [ENTER] buttons

Button Explanation

Ten keys

Use these buttons to edit the patch name or tone name.

For some items, these buttons can also enter a numeric value.

SHIFT

Use this button in conjunction with other buttons to access parameters or to

operate other parameters.

ENTER Press this to conrm a value or execute an operation.

PATCH BANK [1]–[8]/NUMBER [1]–[8] buttons

Button Explanation

PATCH BANK [1]–

[8]

Select patch banks.

When editing, you can use these buttons to select partials.

NUMBER [1]–[8]

Select the patch number.

When editing, you can use these buttons to turn partials on/o.

By simultaneously pressing two of the [1]–[16] buttons, you can connect those two steps with

a tie.

Patch

A “patch” contains sound data and data for the performance functions.

Multiple patches can be saved in patch memory, and freely recalled while you perform.

On D-05, a patch consists of two sounds (the upper tone and lower tone), settings that specify

how they are played, and settings such as keyboard mode, output mode, and reverb.

Tone

The upper and lower tones each consist of two “partials” (sound sources) and common

settings that specify how the partials are controlled.

The common settings include the type selections for the two partials, how the two partials are

combined (the “structure”), and settings such as LFO, pitch envelope, equalizer, and chorus.

Partial

A “partial” is the most basic unit of sound on D-05. There are two types of partial: a synthesizer

sound generator and a PCM sound generator. Synthesizer type partials provide a TVF (Time

Variant Filter) and a TVA, and PCM type partials provide a TVA (Time Variant Amplier).

How the Sound Engine Is Structured

Patch

Patch nameTone Tune

Tone

Balance

Variations of

Control Functions

Tone Tune

Tone

Common

P. ENV LFO1–3

Structure

Equalizer

Tone name

Chorus

Partial (Synthesizer Sound Generator)

Partial (PCM Sound Generator)

Pitch

Waveform

Pulse

width

TVF

Cuto

Resonance

TVF-ENV

Filter envelope

TVA

Level

TVA-ENV

Amp envelope

Pitch

PCM

wave

form

TVA

Level

TVA-ENV

Amp envelope

LFO (Low Frequency Oscillator)

LFO 1 LFO 2 LFO 3

P. ENV

Pitch envelope

Key Mode

Output Mode

(Reverb, etc.)

LOWER Tone

UPPER Tone

Partial 1

Partial 2

Roland D-05 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland D-05

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info