Bedienungsanleitung Rommelsbacher OP700 (Seite 29 von 32) (Deutsch, Englisch)

714264

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Important information on working with your oil press

• Use only seeds and nuts with a high oil content.

• The raw material to be processed must not be larger than peanuts resp. hazelnuts. If necessary,

crush them to ensure optimum processing. To do so, use a mincing knife, for example. Also very small

particles might block the screw conveyor, like e.g. nut crumbs or nut dust, groats or seed powder, which

is produced when pre-treating nuts/seeds in a grinder or blender. In this case we recommend to sieve

the smallest particles before pressing.

• Before ﬁlling in the material to be pressed, pay attention that it does not contain foreign matters such

as small stones etc.

• The seeds and nuts to be processed must be sufﬁciently dried. We recommend to dry them prior to

processing at 60 °C (circulating air) to 80 °C (upper and lower heat) for 2 to 3 hours in the oven to

achieve an optimum oil yield. In ideal circumstances ﬁll in the seeds/nuts when they are still warm. For

storage – also short-term – pack seeds/nuts airtight.

TIP: Start processing with a small amount to test the quality and the moisture content.

TIP: Walnuts are a real hardness test. Ideally use walnuts which have been dried a very long time

(e.g. in a dehydrator, at 50 °C for 24 hours) or nuts from the previous season.

• The appliance is not designed for pressing soya beans or olives.

Error Cause and troubleshooting

Appliance cannot be

switch on.

• Check whether the locking mechanism is correctly locked.

• Check whether the appliance is correctly plugged in.

• Test the socket by connecting another appliance.

• Check whether the power cord or the plug is damaged.

- If they are damaged, do not use the appliance.

• The appliance is heating-up.

- The pilot lamp ﬂashes or is permanently illuminated in red during heating-up.

• Check if the appliance is assembled correctly.

- If necessary, disassemble and re-assemble the appliance.

• Check whether the lid is correctly seated on the seed container.

- Press the lid ﬁrmly.

• Check whether the micro switch at the rear (back upper edge) is clogged.

- Clean the micro switch.

• If the appliance has been used too long, the overheating protection of the

motor is activated.

- Allow the appliance to cool down.

The appliance stops

during operation.

• Check whether the material which has been ﬁlled in (too large, too hard or

too moist) blocks the screw conveyor.

- Clear the blockage. (see section on “Clearing an screw conveyor blockage”).

• Seed container empty. There is not sufﬁcient material in the screw conveyor.

The appliance stops automatically after 1 minute.

- Check if there is sufﬁcient material in the hopper or if it is jammed. Reﬁll

if necessary and restart the appliance.

• Check whether the lid is correctly seated on the seed container.

- Press the lid ﬁrmly.

• If the appliance has been used too long, the overheating protection of the

motor is activated.

- Allow the appliance to cool down.

Trouble shooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rommelsbacher OP700 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info