Bedienungsanleitung Rossmax SB200 (Seite 2 von 2) (Englisch)

783662

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Introduction

ACT (Artery Check Technology)

Error code for your reference

Installing Batteries

Attaching the lanyard

How to use

Rossmax Fingertip Pulse Oximeter SB200 is used to measure

arterial oxygen saturation (% SpO2) of hemoglobin and pulse

rate, an important indicator of your respiratory function. It is

non-invasive device intended for spot-check of adult and

pediatric whose age is over 3 at home, hospital and clinics.

Attention: Consult the accompanying documents. Please

read this manual carefully before use. Please be sure to

keep this manual.

ACT processes the SpO2 signal and determines the elasticity

of blood vessel based on the derived wave form. It further

classifies the vascular status into 6 levels and presents the result

in an intuitive graphical interface.

Artery and blood circulation in excellent con-

dition.

Artery and blood circulation in good to aver-

age condition.

Artery and blood circulation in average condi-

tion.

Artery and blood circulation in below average

condition.

Artery and blood circulation in poor condition.

Artery and blood circulation in critical condi-

tion.

Note: the classification of artery and blood circulation

condition is for reference only, Please consult with

your physician for further advice.

SENSOR ERROR:

Sensor cannot be detected, return the

device to your local distributor or ser-

vice centre.

MEASURE ERROR:

Signals cannot be detected, turn the de-

vice off and measure again.

AC ERROR:

Weak signal for artery check, turn the

device off and measure again.

1. Use thumb to slide battery cover out.

2. Insert or replace 2 “AAA” sized batteries down with the correct

electrical polarity.

You need to replace the batteries when:

1. Low battery icon appears on display

2. The function button is pressed and nothing appears on

display.

Caution: Batteries may leak or explode if used or disposed of

improperly. Remove batteries if the device will be

stored for long time. Do not use different types or

brands of batteries at the same time. Do not mix fully

charged and partially charged batteries at the same

time. The device will automatically shut down in low

battery.

1. Insert the narrow end of the lanyard through the holder.

2. Draw the other end of the lanyard through the loop at the

narrow end and tighten.

1. Open the clip; press the Power On/Off button as .

2. Information of software version appears. Insert one finger(left

hand middle finger is recommended), nail side up, into the

finger opening of the pulse oximeter as .

Note: If no finger insert, the device will auto shut off after 30

seconds.

3. The display shows , pulse oximeter begins its measurement.

Note: Make sure the finger is lying flat. Do not shake and keep

body steady during measurement.

Note: If artery check result cannot be detected, "" will

appear on the screen.

5. Remove the finger, the screen will show artery check level

as .

6. Press button shortly to switch the display to the 3 parameters

(artery check, SpO2 and pulse rate) as .

Note:

1. The SpO2 sensor and photoelectric receiving tube should be

arranged in a way with the subject’s arteriole in a position

there between.

2. Make sure the optical path is free from any optical obstacles

like rubberized fabric.

3. Excessive ambient light may affect the measuring result. It

includes fluorescent lamp, dual ruby light, infrared heater,

direct sunlight and etc.

4. Strenuous action of the subject or extreme electrosurgical

interference may also affect the accuracy.

5. The device has a visual and audio signal when the

measurement of SpO2 is lower than 90%.

Cautionary Notes

- This device is to be operated by trained personnel only.

- The device has intended only for spot-checking, but not

medical result evaluation.

- This device is designed to determine the percentage of arterial

oxygen saturation of functional hemoglobin. Factors that may

degrade pulse oximeter performance or affect the accuracy of

the measurement include the following:

• Do not apply the pulse oximeter on the same arm as a blood

pressure cuff, arterial catheter or infusion line(s).

• Excessive light, such as sunlight or direct home lighting.

• Not steady at the site of application (e.g. trembling).

• Moisture in the device.

• Improperly applied device.

• Finger is too large or too small to fit into the device.

• Poor pulse quality.

• Venous pulsations.

• Anemia or low hemoglobin concentrations.

• Cardiogreen and other intravascular dyes.

• Carboxyhemoglobin.

• Methemoglobin.

• Dysfunctional hemoglobin.

• Artificial nails or fingernail polish.

• On fingers with anatomical changes, oedemas, scars or burns.

Name/ Functions of each part

1. OLED display

2. Pulse strength

3. Pulse search icon

4. Artery check icon

5. Alarm icon

6. Battery indicator

7. Power On/O Button

8. SpO2 icon

9. Pulse icon

10. Battery cover

4. Your SpO2 and pulse rate values will appear on the screen

after few seconds and artery check result will appear on

screen after 30 - 60 seconds as .

RI_IB_SB200(cont)_EN_2Yr_TP_ver2036.indd 2 2020/9/24 下午 04:13:58

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rossmax SB200 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info