Bedienungsanleitung Rotel RA11 (Seite 10 von 13) (Englisch)

489961

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

RA-12, RA-11 Stereo Integrated Ampliﬁer

Speaker Connection

Turn off all the components in the system before connecting the speakers.

The ampliﬁer has color-coded binding post type speaker connectors on

the back panel. These connectors accept bare wire, connector lugs, or

dual banana type connectors. (except in European Community countries

where their use is not permitted)

Route the wire from the ampliﬁer to the speakers. Give yourself enough

slack so you can move the components to allow access to the speaker

connectors. If you are using dual banana plugs, connect them to the wires

and then plug into the backs of the binding posts. The thumbscrews of the

binding posts should be screwed in all the way (clockwise).

If you are using terminal lugs, connect them to the wires. If you are attaching

bare wires directly to the binding posts, separate the wire conductors

and strip the insulation from the end of each conductor. Be careful not

to cut into the wire strands. Unscrew (turn counterclockwise) the binding

post thumbscrews. Place the connector lug or wire around the binding

post shaft. Turn the thumbscrews clockwise to clamp the connector lug

or wire ﬁrmly in place.

NOTE: Be sure there are no loose wire strands that could touch adjacent

wires or connectors.

Phones Output

4

The Phones output allows you to connect headphones for private listening.

This output accommodates standard stereo phone (1/8”) plugs. Plugging

in a set of headphones does not cut off the signal to the outputs. Use the

Speaker Selector to turn off the speakers. The settings of the Function

Selector determines which source is heard.

NOTE: Because the sensitivity of speakers and headphones can

vary widely, always reduce the volume level before connecting or

disconnecting headphones.

Remote Sensor 5

This remote sensor window receives IR commands from the remote control.

Please do not block this sensor.

Display 7

The front panel display shows the source selected, volume level and

tone settings.

USB Input 0

The front USB input can be connected to a iPod, iPhone, MP3 players

or a Bluetooth dongle (supplied) for wireless streaming. With iPod

or iPhones, simply plug the device into the front USB and select USB

function from the source selector. The iPod, iPhone remains active.

Search and play tracks as usual and the music will be played through

the Rotel system.

Bluetooth Dongle

Insert the supplied Bluetooth Dongle into the front USB for wireless streaming

via Bluetooth, from your device (i.e. mobile phones) to the ampliﬁer.

From your mobile device, look for “Rotel Bluetooth” and connect to it.

Connection is normally automatic, but if prompted for a password, please

press “0000” then press ENT on the remote and your device.

Audio Controls

Volume Control

Turn the controls clockwise to increase the volume, or counter clockwise

to decrease the volume. From the remote control press the volume + or

- key to turn the volume up or down. Press the MUTE key to completely

mute the volume.

Balance Control



The Balance Control adjusts the left-to-right balance of the sound output.

The factory default is the center position or “0”. To change the balance

from the front panel, press the MENU8 key to toggle the front display

to BALANCE SETTING mode. Then press the LEFT or RIGHT keys on the

front panel to change the value to LEFT or RIGHT. The value can change

from L15 to R15. From the remote, press the BALC key to access the

BALANCE SETTING menu, the press the LEFT or RIGHT key to adjust.

When ﬁnished, press the EXITG key to exit the menu.

Tone Control Bypass 8



Bass and Treble Control (Tone Control) circuits are bypassed at factory

default to ensure the purest possible sound. The front display will show

TONE BYPASS. To turn on the tone control, press the BYPASSF key

on the remote control. From the front panel press the MENU8 key to

toggle to the Bypass control then press the LEFT or RIGHT keys to turn

bypass on or off.

Bass and Treble Controls



Set the Bass or Treble controls from the front panel by pressing the

8

key to toggle to either the Bass or Treble Setting menu. Then

press the LEFT or RIGHT key to adjust the value. The Bass and Treble

values range from -10 to +10. From the remote control, press the Bass

or Treble key

, then press the LEFT or RIGHT keys on the remote to

adjust the value.

A properly setup high-performance audio system produces the most

natural sound with little or no adjustment of the tone controls. Use these

controls sparingly. Be particularly careful when turning the controls up.

This increases the power output in the bass or treble range, increasing

the load on the ampliﬁer and speakers.

NOTE: Setting the Bass and Treble controls do not automatically turn

on the tone control. To turn on tone control, refer to previous section

Tone Control Bypass.

Function Control

-L



The Function control selects the input signal source. From the front panel

or remote press the corresponding input key to select the source to listen

to.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rotel RA11 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info