Bedienungsanleitung Rotel RCD-991 (Seite 6 von 30) (Deutsch, Englisch, Französisch, Spanisch)

571048

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Fill out and send in the owner’s registration card packed with the

RCD-991. Also be sure to keep the original sales receipt. It is your

best record of the date of purchase, which you will need in the

event warranty service is required.

Placement

Use common sense when placing the RCD-991 in a cabinet or

when stacking other equipment. Make sure that the shelf or cabi-

net can support its weight. Do not stack heavy components on top

of the RCD-991. Avoid placing the unit where it may be subject to

excessive heat such as on top of a large power amplifier or near a

heat register. For best performance, avoid placing the unit where

it may be subject to vibration, such as near a speaker.

AC Power and Control

AC Power Input

Your RCD-991 is configured at the factory for the proper AC volt-

age in the country where you purchased it (either 115 volts or 230/

240 volts. The AC line configuration is noted on a decal on the

back panel.

Note: Should you move your CD player to another country, it may

be possible to reconfigure it for use on a different line voltage. Do

not attempt to perform this conversion yourself. Opening the en-

closure of the RCD-991 exposes you to dangerous voltages. Con-

sult a qualified service person or the Rotel factory service

department for information.

The RCD-991 should be plugged directly into a 2-pin polarized wall

outlet or into the switched outlet on another component in your

audio system. Do not use an extension cord.

Be sure the power switch on the front panel of the RCD-991 is

turned off (in the "out" position). Then, connect the supplied power

cord to the AC power receptacle on the rear of the unit and the

AC power outlet.

If you are going to be away from home for an extended period of

time such as a month-long vacation, it is a sensible precaution to

unplug your CD player (as well as other audio and video compo-

nents) while you are away.

Power Switch

and Power Indicator

The power switch is located on the front panel of your CD player.

To turn the CD player on, push the switch in. The LED indicator

above the switch and the DISPLAY will light up, indicating that the

CD player is turned on. To turn the CD player off, push the button

again and return it to the "out" position.

Note: If you are using a switched outlet to turn on and off your

CD player, you should leave the power switch in the "on" position.

When AC power is applied to the unit, it will power up in fully ac-

tive mode.

Output Connections

The RCD-991 gives you a choice of analog or digital output sig-

nals. The analog output signal from the built-in Digital to Analog

converter is used with conventional analog audio components.

The digital output, which provides an unprocessed digital data

signal, is used with outboard D/A converters or digital processors.

Note: To prevent loud noises that neither you nor your speakers

will appreciate, make sure the CD player is turned off when you

make any signal connections.

Analog Outputs

[See Figure 2 for wiring illustration]

The analog output signal is available from two different types of

connectors on the back panel of the RCD-991. A pair of standard

RCA jacks supplies a conventional unbalanced analog output sig-

nal from the RCD-991 to the source inputs of an audio preamplifier,

integrated amplifier, or receiver. Alternatively, a pair of three-pin

XLR-style jacks supplies a balanced-line analog output signal for

use with preamplifiers that are equipped with similar input con-

nections.

RCA connections are found on virtually all components. Not as

many components feature XLR connections, but, when available,

they may provide less chance of noise and improved signal qual-

ity. Use whichever type of signal connection matches your par-

ticular system configuration.

Select high quality audio interconnect cables. Connect the left

channel output of the RCD-991 to the left channel source input on

the preamplifier or other component. Connect the right output of

the RCD-991 to the right channel source input on the preamplifier

or other component.

Digital Outputs

and Switch

[See Figure 3 for wiring illustration]

If you are using the RCD-991 as a disc transport with an outboard

D/A converter or other digital processor, you need an unproc-

essed digital data stream from the RCD-991, taken before the

built-in D/A converter. This signal is supplied by the RCD-991’s

back-panel digital output jacks.

Both optical and coaxial digital signal connectors are provided.

Use whichever type best matches your other components. Using a

standard 75 ohm coax or optical digital cable, connect the appro-

priate RCD-991 digital output jack to the digital input connector on

the outboard D/A converter.

A switch to the right of the digital outputs enables or disables the

digital outputs. To use the digital outputs, this switch must be in

the on position. If you are not using the digital outputs, we recom-

mend turning the switch off, because it removes the digital output

circuitry from the signal path.

STEREO COMPACT DISC PLAYER RCD-991

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rotel RCD-991 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Rotel RCD-991

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info