Bedienungsanleitung Rowenta HC1037 (Seite 6 von 40) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Finnisch)

763450

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

•The appliance must be unplugged:

-before cleaning and maintenance procedures.

- if it is not working correctly.

-as soon as you have finished using it.

- if you leave the room, even momentarily.

•Do not use if the cord is damaged.

•Do not immerse or put under running water, even for cleaning purposes.

• Do not hold with damp hands.

•Do not hold the appliance by the casing, which is hot, but by the handle.

•Do not unplug by pulling on the cord, rather pull out by the plug.

• Do not use an electrical extension lead.

• Do not clean with abrasive or corrosive products.

•Do not use at temperatures below 0°C and above 35°C.

GUARANTEE : Your appliance is designed for use in the home only. It should not be used for professional pur-

poses. The guarantee becomes null and void in the case of improper usage.

9. TIPS FOR A SUCCESSFUL HAIRCUT

• Use the hair trimmer on clean, dry hair

• Dry the hair in the direction of the hairstyle you wish to obtain

• Position the person whose hair you are going to cut in such a way as to be able to see the top of

his/her head (Fig. 5)

Before starting a cut, examine the hollows and bumps on the head, which are often located at the

nape of the neck (if you place the trimmer directly against a bump, you will obtain a lighter area).

• At the beginning, only cut a small quantity of hair, until you are familiar with the length left by each

comb.

• Never stop the trimmer in mid-stroke.

• Start with the comb with the highest number (i.e. the one which leaves the most hair) before using

another comb.

Key :

=easy cut

= cut which requires some practice

= difficult cut

10. FOR A SUCCESSFUL ROUND CREW CUT

BASIC METHOD

With this method, the cut follows the shape of the skull.

• Combs necessary for this cut: 3 mm, 9 mm, 18 mm (fig. 6).

• Do not forget to change the comb as you progress through the hair.

1st STAGE : THE CUT.

a) Nape.

• Brush the hair.

• Begin by cutting the hair at the nape upwards, using comb 18 mm.

• Hold the trimmer firmly against the hair, with the comb's teeth pointing slightly upwards (fig. 7).

• Slowly raise the hair trimmer towards the top and outside of the hair, cutting only a small amount of

hair at a time (fig. 8).

• Once the hair at the nape has been evenly cut using comb 18 mm, replace the removable comb in

order to obtain the required length and repeat the first 3 operations.

• Stop the cut at regular intervals, comb the hair and check the result.

b) Sides and top

• Repeat the above operations to cut the sides.

• Change the comb as you change areas (see fig. 6).

• For the top, use the same technique, cutting the hair from the forehead to the crown, against the "lie

of the hair" (fig. 9). Then, level off to match the sides.

2nd STAGE : CONTOURS AND FINISH

a) Nape and sideburns

NOT HC103 039236:039236 18/09/08 10:23 Page 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rowenta HC1037 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info