Bedienungsanleitung Russell Hobbs 24731-56 (Seite 4 von 72) (Alle Sprachen)

705906

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

9. Turn the speed control to the speed you want (1 = low, 2 = high).

10. Turn the speed control back to 0 to turn the motor o.

11. Turning the speed control anti-clockwise to Y will give you a short burst at high speed. In this

direction, the knob is spring-loaded. When you let go, it’ll return to 0.

USING THE BLENDER

1. Lower the blender jug on to the motor unit, then turn the jug clockwise, to lock it in place.

2. Remove the lid.

3. Put the ingredients into the blender jug.

4. Replace the lid.

5. Align the pips on the cap with the slots in the hole in the lid, t the cap, and turn it clockwise to lock it.

6. Don’t run the appliance without tting the cap.

7. To add ingredients while the blender is working, remove the cap, pour the new ingredients through

the hole, then replace the cap.

8. Once nished, switch the appliance o (0) and unplug it.

9. Turn the blender jug anti-clockwise, and lift it o the motor unit.

CRUSHED ICE

1. For best results, full the jug with between 150ml and 500ml of ice cubes.

2. Put the lid on the blender, then:

3. Turn the speed control to Y for a second or two, then release it.

4. Check the results, and adjust.

USING THE PROCESSOR

1. Switch the appliance o () and unplug it.

2. Fit the spindle to the top of the motor unit.

3. Lower the jug on to the motor unit, then turn the jug clockwise, to lock it in place.

4. Choose the attachment you need.

5. Hold the lid with the tube slightly behind the jug handle, set it on the jug, then turn it clockwise, to

lock the tab into the top of the handle.

6. Once nished, switch the appliance o (0) and unplug it.

7. Turn the jug anti-clockwise, and lift it o the motor unit.

USING THE CHOPPER/MIXER/CREAMER ATTACHMENT

Use the chopper for pulverizing ingredients.

Use the mixer to mix ingredients together.

Use the creamer to thicken cream, to beat eggs, and to cream eggs and sugar together.

1. Fit the desired attachment onto the drive shaft and slide it to the bottom.

2. Lower the drive shaft into the bowl over the spindle.

3. Put the ingredients into the jug.

4. Hold the lid with the tube slightly behind the jug handle, set it on the jug, then turn it clockwise, to

lock the tab into the top of the handle.

5. To add ingredients while the motor is running, lift the pusher out of the tube, add the ingredients

through the tube then replace the pusher.

6. To remove the lid, turn it anti-clockwise to unlock it, then lift it o.

SLICING/GRATING

1. Lower the disc over the top of the spindle.

2. Hold the lid with the tube slightly behind the jug handle, set it on the jug, then turn it clockwise, to

lock the tab into the top of the handle.

3. Remove the pusher, and drop the ingredients down the tube.

4. Replace the pusher, and use it to push the ingredients gently down the tube.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Russell Hobbs 24731-56 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info