Introduction
The Next Generation of Universal Remote Control
Congratulations purchasing easytip, the universal infrared remote
control for your TV set SAT-Receiver and VCR.
Easytip is a product of high quality
All information on this product is published with no consideration
for possible patent rights. Trademarks are mentioned without gu-
arantee of their free use.
Although a lot of care was taken when creating this manual with
its text and graphic images, errors can never be completely elimi-
nated.
Therefore, the manufacturer cannot be made liable for faulty sta-
tements and their possible consequences.
You are very welcome to contact the manufacturer for report er-
rors and to make suggestions for improvement.
© 1999 by ruwido
All rights reserved, including rights of photomechanical reproduc-
tion and electronic storage.
Printed in Austria.
ruwido-austria
Köstendorfer Straße 8
A-5202 Neumarkt am Wallersee
tel. +43(0)6216/4571
fax +43(0)6216/457126
e-mail: service.easytip@ruwido.com
Internet: http://www.ruwido.com
4
English
5
English
Inserting and changing the batteries
Your easytip is powered by two (alkaline) 1.5 V batteries (IEC LR
03, AAA)
Insert the batteries following the markings in the battery compart-
ment.
After inserting the batteries, your easytip is adjusted for TV-
operation.
If the LED does not blink as usual when pressing the keys or if
the device you are controlling fails to respond from the usual
distance then the batteries must be changed.
Your easytip includes a intermediate memory which prevents the
easytip from losing its memory during the battery changing.
Please dispose batteries carefully.
Description of keys
Image
a Light-emitting diode (LED)
b Level key to switch to device level (TV, SAT and VCR)
c Number keys: 0-9
d -/--: single/double digit enter, 10, 1-
e Power/Standby on/off
f P+/P-: switch to next or previous channel
g +/- Vol: Volume control
h Mute: Sound on/off
i OK/Norm:
For TV: Reset TV set to basic settings and confirmation-key for
TV-menu
For SAT: Confirmation-key for menu of receiver
j • For TV: Using the teletext-function
k • For TV: Function of the Videotext-keys
For SAT: Radio: Radio operation
TV/SAT: Switch between TV/SAT
l Menu: calls the menu-function for TV and SAT
m Info: calls the Info-function, Index, S 100
n AV: switch to the AV-channel (e.g.: VCR, SAT)
o Shift: preselection key for adjustment of brightness, color,
contrast, treble, bass, balance.
Programming easytip
Programming by Code entering
1. Switch on the device you want to use your easytip with.
2. Turn to the TV code list (other manual) and look for the name
of your device manufacturer.
3. Choose your device by using the Level key (image b) and
press the key (for about 5 seconds) until the LED (image a)
blinks twice.
NOTE: The AUX-mode (image b) can be programmed any way
(alternate TV set, alternate SAT-receiver).
After the LED (image a) flashing twice, press either TV or SAT,
depending on which advice you want to have on the AUX-mode
(image b).
4. Enter the first 3-digit code from the list with the number keys
(image c) on your remote control.
ATTENTION!
The first figure of the 3-digit cod must be entered within 5 sec-
onds of the LED (image a) blinking twice.
Otherwise the LED (image a) will flash once and you will have to
repeat the procedure from step 3.
5. After the 3-digit code has been entered the LED (image a) will
blink twice to indicate that the code has been accepted.
ATTENTION!
If you entered the first digit within 5 seconds but still see one long
flash from the LED (image a) after you have entered the code,
Bedin ET4 Version 1 07.03.2001 14:25 Uhr Seite 4
