English
English
6
4. Enter the first 3-digit code from the list with the number keys
(image a) on your remote control.
ATTENTION!
The first figure of the 3-digit cod must be entered within 5 sec-
onds of the LED (image a) blinking twice.
Otherwise the LED (image a) will flash once and you will have to
repeat the procedure from step 3.
After the 3-digit code has been entered the LED (image a) will
blink twice to indicate that the code has been accepted.
ATTENTION!
If you entered the first digit within 5 seconds but still see one long
flash from the LED (image a) after you have entered the code,
this means the code you entered is invalid.
In this case, repeat the procedure from step 3.
Now point your easytip at your device and try to operate your de-
vice with your Easytip.
If your device does not react to the device code number you
entered or if it operates incorrectly, enter the next number listed
against the device manufacturerís name.
The code list shows the most common codes first.
If none of the code numbers listed in the code list work properly
use the Code search function.
Make a note of your 3-digit code numbers.
NOTE: By entering code 000 you can restore the basic settings
of your easytip. You can then program easytip newly.
Code Search
If none of the codes listed for your device work or if a previously
entered code number no longer works or works unsatisfactorily,
use the code search.
1. Switch on chosen device.
2. TV, VCR, SAT
Choose the device you want to adjust by using the Level key
(image b) and press the key (for about 5 seconds) until the
LED flashes twice. Continue with step 3.
CD, TAPE, TUNER
Press the Preselection key (image c) to get to the AUDIO-
mode. Then choose the device you want to adjust by pressing
the Level key (image b) and keep it pressed (for about
5 seconds) until the LED (image a) blinks twice. Continue with
step 3.
AMPLIFIER
Press the Preselection key (image c) to get to the AUDIO-mo-
de. Then choose the device you want to adjust by pressing
the level key (image b) and keep it pressed (for about 5 se-
conds) until the LED (image a) blinks twice. Then press the
Preselection key “TUNER” (image c) briefly to get to the
AMPLIFIER-mode. Continue with step 3.
3. Enter code 001 (code search) with the number keys. The LED
(image a) blinks twice.
4. Manual operation: Keep pressing the Power/Standby-key
(image f) for TV, SAT and AMPLIFIER, the Stop-key (image k)
TV
VCR
SAT
CD
TAPE
TUNER
AMPLIFIER
7
for VCR, CD and TAPE or the Numberkey 2 (image d) for TU-
NER at short intervals, until the device shows reaction.
Automatic operation: Press the Power/Standby-key (image
f) for TV, SAT and AMPLIFIER, the Stop-key (image k) for VCR,
CD and TAPE or the Numberkey 2 (image d) for TUNER, until
your device shows reaction.
Every 1.5 seconds the TV code is continued automatically and
the appropriate standby command is sent.
5. When your easytip has found the right code your device
switches off and you can then release the key.
Continue with step 5.
6. Now press the Level key (image b) again until the LED (image
a) blinks twice. This shows you that your easytip has stored
the appropriate code number.
Now check the function of your remote control. If your easytip
does not react to the code number it has found, repeat steps
1 to 5 until you have found a optimal code number.
ATTENTION!
A new code search begins with the last code number found in
the previous search. When the end of the code list is reached the
LED will blink three times. The search is then repeated from the
beginning. Please be patient. There may be many codes to se-
arch through before the code for your equipment is found.
Changing the direction or the search:
It is possible, particularly in automatic search mode, to skip over
the relevant code by mistake. In this case, you can reverse the
direction of the search for a maximum of 5 codes by pressing the
Vol-key (image h).
ATTENTION!
After 5 codes the search direction changes back automatically.
If you want, you can press the Vol+ -key (image h) to change
back to the original search direction.
Adjusting color, contrast, bass, treble,...for your TV set
1. Press the Level key (image b).
2. Briefly press the Shift-key (image p).
3. Press the wanted key within 5 seconds.
Numberkey 1 (image d) = Brightness
Numberkey 2 (image d) = Color
Numberkey 3 (image d) = Contrast
Numberkey 4 (image d) = Treble
Numberkey 5 (image d) = Bass
Numberkey 6 (image d) = Balance
4. You can adjust your device by using keys Vol- (image h) and
Vol+ (image h).
5. After the end of adjusting, wait for about 5 seconds until the
keys get back their normal function.
Querying the Code Numbers
You will need this function to query the code found by the auto-
matic code search, so that you can note it down in this operating
manual.
1. Press the chosen Level key (TV, SAT, VCR, CD,...) (image b)
until the LED blinks twice.
2. Now enter code 002 for query mode.
ATTENTION!
The first figure of the 3-digit cod must be entered within 5 se-
conds of the LED (image a) blinking twice.
Otherwise the LED (image a) will flash once and you will have to
repeat the procedure from step 1.
Bedin ET7 Version 1 07.03.2001 14:22 Uhr Seite 6
