Bedienungsanleitung Ryobi LDD 1802 (Seite 10 von 89) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

491258

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

English

E I

P NL

S DK N FIN GR

H CZ RUS PL

SLO TR

OPERATION

BATTERY PROTECTION FEATURES

Ryobi 12 V lithium-ion batteries are designed with

features that protect the lithium-ion cells and maximize

battery life. Under some operating conditions, these

built-in features may cause the battery and the tool it is

powering to act differently from nickel-cadmium batteries.

During some applications, the battery electronics may

signal the battery to shut down, and cause the tool to

stop running. To reset the battery and tool, release the

trigger and resume normal operation.

NOTE: To prevent further shut down of the battery, avoid

forcing the tool. Switching to a lower speed will also

prevent shut down.

If releasing the trigger does not reset the battery and

tool, the battery pack is depleted. If depleted, the battery

pack will begin charging when placed on the lithium-ion

charger.

ADJUSTING THE TORQUE (Fig. 3)

The tool is equipped with an adjustable torque clutch for

driving different types of screws into different materials.

Adjust the torque as necessary.

SWITCH (Fig. 4)

n To turn your drill ON, depress the switch trigger.

n To turn it OFF, release the switch trigger.

VARIABLE SPEED

This tool has a variable speed switch that delivers higher

speed with increased trigger pressure. Speed is controlled

by the amount of switch trigger depression.

SWITCH LOCK (Fig. 4)

The switch trigger can be locked in the OFF position.

This feature can be used to prevent the possibility of

accidental starting when not in use. To lock switch trigger,

place the direction of rotation selector (Forward/Reverse

Selector) in center position.

Note: When selector is in center position, switch trigger

is locked.

REVERSIBLE (Fig. 4)

This tool has the feature of being reversible. The direction

of rotation is controlled by a selector located above the

switch trigger. With the drill held in normal operating

position, the direction of rotation selector should be

positioned to the left of the switch for drilling. The drilling

direction is reversed when the selector is to the right

of the switch. When the selector is in center position,

the switch trigger is locked. To stop, release switch trigger

and allow the chuck to come to a complete stop.

ELECTRIC BRAKE

This drill has an electric brake. When the trigger switch

is released, the chuck stops turning. When the brake is

functioning properly, sparks will be visible through the

vent slots on the housing. This is normal and is the action

of the brake.

KEYLESS CHUCK (Fig. 5)

Your drill has a keyless chuck. As the name implies, you

can hand tighten or release drill bits in the chuck jaws.

Hold the body with one hand and rotate the chuck with

your other hand. The arrows on the chuck indicate which

direction to rotate the chuck body in order to LOCK

(tighten) or UNLOCK (release) the drill bit.

WARNING

Do not hold chuck body with one hand and use

power of the drill to tighten chuck jaws on drill

bit. Chuck body could slip in your hand or your

hand could slip and come in contact with rotating

drill bit. This could cause an accident resulting in

serious personal injury.

ADJUSTING THE SPEED (Fig. 6)

Follow these steps to adjust the speed.

n For high speed: Slide the two-speed gear train switch

to “2.”

n For low speed: Slide the two-speed gear train switch

to "1."

Note: If you have difficulty changing from one gear

range to the other, turn the chuck by hand until the

gears engage.

CAUTION

To prevent gear damage, always allow chuck to

come to a complete stop before changing the

speed or the direction of rotation.

961067016-02.indd 10961067016-02.indd 10 3/24/08 4:46:17 PM3/24/08 4:46:17 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi LDD 1802 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info