Bedienungsanleitung Ryobi LSDT1202 (Seite 8 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

513654

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

English

FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR

punch to mark the desired hole location. This will

prevent the drill bit from slipping off-center as the hole

is started.

 When drilling metals, use a light oil on the drill bit to

keep it from overheating. The oil will prolong the life of

the bit and increase the drilling action.

 If the bit jams in the workpiece or if the drill stalls,

stop the tool immediately. Remove the bit from the

workpiece and determine the reason for jamming.

NOTE: This drill has an electric brake. When the switch

trigger is released, the chuck stops turning. When the

brake is functioning properly, sparks will be visible through

the vent slots on the housing. This is normal and is the

action of the brake.

WOOD DRILLING

For maximum performance, use high speed steel bits for

wood drilling.

 Begin drilling at a very low speed to prevent the bit

from slipping off the starting point. Increase the speed

as the drill bit bites into the material.

 When drilling through holes, place a block of wood

behind the workpiece to prevent ragged or splintered

edges on the back side of the hole.

METAL DRILLING

For maximum performance, use high speed steel bits for

metal or steel drilling.

 Begin drilling at a very low speed to prevent the bit

from slipping off the starting point.

 Maintain a speed and pressure which allows cutting

without overheating the bit. Applying too much

pressure will:

 overheat the drill

 wear the bearings

 bend or burn bits

 produce off-center or irregular-shaped holes

 When drilling large holes in metal, start with a small

bit, then finish with a larger bit. Also, lubricate the bit

with oil to improve drilling action and increase bit life.

MAINTENANCE

WARNING

When servicing, use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

Avoid using solvents when cleaning plastic parts.

Most plastics are susceptible to damage from various

types of commercial solvents and may be damaged by

their use. Use clean cloths to remove dirt, dust, oil, grease,

etc.

WARNING

 

based products, penetrating oils, etc., come in contact

with plastic parts. They contain chemicals that can

damage, weaken or destroy plastic.

Do not abuse power tools. Abusive practices can damage

tool as well as workpiece.

WARNING

Do not attempt to modify this tool or create accessories

not recommended for use with this tool. Any such

       

in a hazardous condition leading to possible serious

personal injury.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing

of as waste. The machine, accessories

and packaging should be sorted for

environmental-friendly recycling.

SYMBOL

Safety Alert

V Volts

Hertz

Direct current

Alternating Current

Watts

No-load speed

min

Revolutions or reciprocations per minute

Recycle unwanted

CE Conformity

Double insulation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi LSDT1202 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info