628422

SAB Heli Division Head HPS3 - H0430-K Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
B
Swashplate
[H0420-S]
- 1 x Swashplate Assembly.
- 2 x Bearings 30x
37x4mm.
- 6 x Uniballs M3x4
5 H3.
- 1 x Uniball M3x4
5 H18.
- 3 x Socket Head Cap Screws M2x5mm.
- 4 x Socket Head Cap Screws M2x8mm.
- 3 x Swasher
2x
5x0.5mm
Radius Arm
[H0421-S]
- 1 x Center Hub.
- 1 x Socket Head Cap Screws
M3x12mm.
- 1 x Socket Head Cap Screw
Shouldered M4x25mm.
- 1 x Metric Hex Nylon Nut M4.
Center Hub
[H0410-S]
- 2 x Radius Arms.
- 2 x Spacer Arm
3x
5x2.7mm.
- 1 x Spacer Hex.
- 1 x Uniball Radius Arms.
- 2 x Socket Head Cap Screws M3x16mm.
- 2 x Socket Head Cap Screws M2.5x10mm.
- 2 x Flanged Bearings
2.5x
6x2.5mm.
- 4 x Flanged Bearings
3x
7x3mm.
Linkage
[H0417-S]
- 2 x Linkages
M3x50mm.
- 4 x Plastic Ball Links.
Damper Derlin
[H0426-S]
- 3 x H0426-A.
- 3 x H0426-B.
- 3 x H0426-C.
- 3 x Washers
10x
16x1mm.
- 3 x Washers
10x
16x0.2mm.
- 3 x Orings 3050.
Recommendations
- These parts should be used only with models SAB Goblin
- Please follow all the instructions shown in the Goblin main manual. In this manual please read Chapther 2, Important notes
- Use Loctite on all threads.
- Put a small amount of grease inside the hub and the O-Ring.
- Check for axial play of the spindle at least after the first 10 flights and add shims if necessary.
- Firmly tighten the blades before flight.
About HPS
HPS stands for "High Precision System". This head has been
developed in order to increase the usable rotor RPM range without
having to change the rigidity of the dampening system.
The new head is developed specially to limit the teetering effect of
the spindle by means of dampening achieved by a special
technopolymer material.
The maximum teetering amount can be adjusted based on the
amount of play shown in figure "A" of the drawing. The O-ring is
necessary to create a radial and axial preload.
The preload can be kept relatively low, thanks to the mechanical
locking properties of the technopolymer dampeners.
With this solution, finding the correct preload is less complex.
This solution is safer because there is a physical "stop" of the
teetering effect with the technopolymer dampers, also with low
axial preload.
The change of preload will serve exclusively to customize the
response of the model.
Furthermore, the spindle can only move vertically thanks to the
elongated hole shown in section "B" of the drawing.
This solution allows an optimal control of the geometry even when
large amounts of torque are introduced into the system.
The head is very accurate and reliable.
Spare Parts
- 2 x Blade Grip.
- 2 x
Thrust Bearing
10x
18x5.5mm.
- 4 x
Bearing
10x
19x5mm.
- 2 x Washer
10x
16x1mm.
- 2 x Button Head Socket Cap M4x8mm.
Blade Grip
[H0182-S]
- 2 x Blade Grip Arm.
- 2 x Socket Head Cap
Screw M4x10mm.
- 2 x Uniball M3x4 Ø5 H3.5.
Blade Grip Arm
[H0183-S]
Spindle Shaft
[H0412-S]
- 2 x Spindle Shaft.
- 2 x Pin 5mm.
- 4 x Socket Head Cap
Screw M2.5x6mm.
- 2 x Socket Head Cap
Screw M4x10mm
- 2 x Washer Ø6,3 x Ø15 x 1mm
ABOUT HPS3
The new HPS 3 head offers an independent dampening system for
each blade grip, there are three dampening settings:
A = Soft for smooth response.
B = Medium.
C = Firm for direct and precise response.
We recommend starting with the medium setting.
For safety reasons we suggest to not exceed 2300 rpm.
In addition, we recommend using a smaller tail pulley in order to
increase the tail rotor speed to counteract the additional torque
introduced by the 3rd rotor blade. You will find a 24T tail rotor pulley
in the kit for this purpose.
TIPS:
Left Side
Right Side
* To remove the dampeners, you
can use a flathead screwdriver
through the hole as shown.
* Clock-wise, counter clock-wise thread
* By turning the linkages you can adjust
tracking. If tracking is adjusted correctly,
you’ll see the metal part line up around
in the center of the opening.
Detail B
SPARE PARTS
RECOMMENDATIONS
These parts should be used only with models SAB Goblin.
· URUKAY and G770 (recommended blades SAB 3BL730, max 750 mm)
· Goblin 700 (recommended blades SAB 3BL690, max 710 mm)
· Goblin Speed (recommended blades SAB 3BL720-1D, max 720 mm)
- 3 blade rotor heads require a much lower cyclic gain on flybarless systems.
We recommend that you set your gain at least 30% lower than the gain
you normally use on your 2 blade rotor head helicopters.
You can start increasing the gain after you complete your first flight.
Running too high of a gain can induce a violent oscillation that can
potentially cause damage to your helicopter in flight.
- Please follow all the instructions shown in the Goblin main manual.
In this manual please read Chapter 2, Important notes
- Use Loctite on all threads.
- Put a small amount of grease inside the hub and the O-Ring.
- Check the spindle for axial play at least after the first few flights and add
shims as necessary, slight axial preload is optimal.The blade grips must
move freely, but they should not move just under their own weight.
- Firmly tighten the blades before flight.
Page 2
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für SAB Heli Division Head HPS3 - H0430-K wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info