Bedienungsanleitung Sagem MLP1300 (Seite 2 von 16) (Englisch)

489663

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

IMPORTANT SAFEGUARDS

INSTALLATION

Do not place the unit in direct sunlight, near heaters or

heat radiating applications.

Do not expose this unit to dust, smoke or steam which

may harm internal components.

Handle the unit carefully. Dropping or jarring may

damage internal components.

Do not place heavy objects or liquids on the top of the

unit. Spilled liquids may cause damage.

Do not

INSTALLATION ON THE CEILING

The ceiling must be strong enough to support the unit and

the installation must be in accordance with any local build-

ing codes. The unit must be installed by qualified service

personnel.

push objects of any kind through openings of this

projector as they may touch dangerous voltage points or

short-out parts that could result in a fire or electric shock.

Do not use this projector near water or in contact with water.

Do not use the unit while the temperature is high or varies

greatly. The unit must be used at environment temperature

between 5 C (41 F) and 35 C (95 F).

POWER SUPPLY

This unit is designed to operate on a power supply of

100~240VAC, 50 - 60 Hz.

Be sure that your power supply fits the above requirement

before attempting to use the unit.

Before disconnecting the power cable, make sure you

have followed the shut-off procedure.

Disconnect the power cable from the power outlet after

using the unit.

If you are not sure of the type of power, please consult

your appliance dealer or local power company.

CLEANING

Make sure to unplug the power cable before cleaning.

Do not use water, liquid aerosol cleaners, strong detergents

or solvents such as alcohol. Please use damp cloth and wipe

on the cabinet gently.

Use a blower or lens paper to clean the lens. Be careful not

to scratch or mar the lens.

Use a vacuum cleaner to clean periodically the

ventilation slots and speaker grills or change the air filter

(see p15). Accumulated dust on the ventilation slots may

cause the unit over-heated and lead to malfunction.

CARRYING AROUND

Please use the carrying case to carry this unit and make

sure the lens is protected with lens cap.

Do not subject this unit to strong mechanical shock.

LAMP REPLACEMENT

Under normal usage, the life time of lamp is about 1500

hours. The output luminance will drop as lamp life

diminishes. User can check the lamp life status in the

MENU of projector.

Change the lamp cartridge when the brightness is no more

acceptable (see p16 for instruction).

CAUTION

Do not put your hand or any object near the ventilation slots because the air is hot.

Do not look into the lens while the unit is operating. Strong light may cause harm to your eyes.

Do not block ventilation openings to prevent inside components from overheating.

WARNING

Handle the power cable carefully and avoid excessive bending. A damaged cable may cause electric shock or fire.

Do not expose this unit to rain or moisture to prevent fire or shock.

Do not open the cabinet to avoid electrical shock. Refer all servicing to qualified service personnel.

IMPORTANT SAFETY NOTICE

PRECAUTIONS

Please read this manual carefully before using the projector and keep this manual handy for future reference.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sagem MLP1300 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sagem MLP1300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info