Bedienungsanleitung Salus CT100 (Seite 2 von 2) (Englisch)

542005

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

PRODUCT COMPLIANCE

This product complies with the essential requirements

of the following EC Directives:

•

Electro-Magnetic Compatibility

Directive 2004/108/EC

•

Low Voltage Directive 2006/95/EEC

•

EC Marking Directive 93/68/EEC

SAFETY INFORMATION

These instructions are applicable to the Salus Controls

model stated on the front cover of this manual only,

and must not be used with any other make or model.

These instructions are intended to apply in the United

Kingdom only, and should be followed along with any

other statutory obligations.

This accessory must be fitted by a Competent person,

and installation must comply with the guidance

provided in the current editions of BS7671 (IEE Wiring

Regulations) and Part ‘P’ of the Building Regulations.

Failure to comply with the requirements of these

publications could lead to prosecution.

Always isolate the AC Mains supply before carrying

out any work on the CT100 thermostat.

Please leave these instructions with the end user where

they should be kept in a safe place for future reference.

INTRODUCTION

The CT100 from Salus Controls is a practical surface

mounted mechanical thermostat. The thermostat can

be used to switch a circulating pump, boiler or most

common motorised zone valves.

The CT100 will allow the user to control the

temperature of Domestic Hot Water Cylinders (both

uninsulated and foam lagged), and is also supplied

with a wire strap which enables the unit to be used as

a pipe thermostat.

FEATURES

•

Surface mounted

•

Suitable for use on uninsulated

and foam lagged cylinders

•

Easy temperature adjustment

•

Dual use (cylinder or pipe thermostat)

INSTALLATION

Please read the important safety information at the

start of this manual before you begin to install the

device.

NOTE: All electrical installation work should be

carried out by a suitably qualified Electrician or

other competent person.

If you are not sure how to install this thermostat consult

either with a qualified electrician, heating engineer or

your boiler / heating system supplier for advice on how

to continue.

The CT100 thermostat should not be mounted in a

location where it will come into direct contact with

water, moisture or condensation. The location should

also be accessible for the connection of the control

wiring.

There are few electrical connections required to the

CT100, and these connections should be made to the

screw terminals on the front of the thermostat, as

indicated in the diagrams below:

Terminal Description Function

C Common Contact ---

1 Normally Closed Contact made when

Contact temperature drops

2 Normally Open Contact made when

Contact temperature rises

Earth ---

Fitting Location

When installed as a cylinder thermostat: The

recommended fitting location is approximately a

quarter of the way up from the bottom of the cylinder

– if the thermostat is to be mounted on a foam lagged

cylinder, a sufficient amount of insulation (to the depth

of the cylinder surface) must be removed to allow the

CT100 to be in contact with the cylinder.

When installed as a pipe thermostat: The CT100

thermostat should be located as near to the

temperature source to be controlled as possible,

typically not more than 0.6 metres from the boiler.

OPERATION

The CT100 thermostat switches on and off the heat

supply from the boiler to the hot water cylinder. It

works by sensing the temperature of the water inside

the cylinder, switching on the water heating when the

temperature falls below the thermostat setting, and

switching it off once this set temperature has been

reached.

The CT100 thermostat has an easily adjustable, clearly

marked scale, and the temperature should normally be

set at between 60 ºC and 65 ºC. This temperature

setting is high enough to kill off any harmful bacteria in

the water - raising the temperature of the stored hot

water any higher will result in wasted energy and

increases the risk of scalding.

If your boiler has a control thermostat it should always

be set to a higher temperature than the cylinder

thermostat. In most boilers, a single boiler thermostat

controls the temperature of water sent to both the

cylinder and radiators, although in some there are two

separate boiler thermostats.

Turning a cylinder thermostat to a higher setting will

not make the water heat up any faster. How quickly the

water will heat up depends on the design of the

heating system.

CT100 INSTRUCTION MANUAL

CT100 Manual_Layout 1 18/05/2012 09:57 Page 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Salus CT100 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info