Bedienungsanleitung Samson MDR6 (Seite 7 von 76) (Deutsch, Englisch, Französisch, Spanisch)

24759

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

ENGLISH

Front and Rear Panel Layout

FRONT PANEL

1 MIC/LINE – Combination Input connector for Low-Noise

Microphone pre-amp and Line level inputs.

2 GAIN – Used to set the input level of the mic pre and line

input.

3 CLIP – Red LED will illuminate indicating when the mic GAIN

has been adjusted too high.

4 HIGH FREQUENCY – Controls the high band of the Channel

Equalizer, +/- 15 dB at 12KHz.

5 MID FREQUENCY – Controls the mid band of the Channel

Equalizer, +/- 15 dB at 2.5KHz.

6 LOW FREQUENCY – Controls the low band of the Channel

Equalizer, +/- 15 dB at 80Hz.

7 AUX – Pre fader auxiliary send that can be used with an exter

nal effects processor, or to create a cue or monitor mix.

8 PAN – Controls the channel’s position between left and right

in the stereo bus.

9 RECORD – Used in the HDM (HARD DISK MODE) to assign the

channel to the Record bus.

10 FADER – 60 mm audio taper fader provides smooth control

over level changes.

11 STEREO MIC/LINE - Combination Input connector for

Low-Noise Microphone pre-amp and Left Line Input for the

stereo channels.

12 RIGHT LINE – Right Line Input connector on the stereo chan

nels.

13 AUX RET – Input connector from external line level sources.

14 CONTROL ROOM – Left and Right output connectors for con

necting a monitor system.

15 MIX – Left and Right main Mix output connectors.

16 AUX OUT – Line level output from the Auxiliary bus.

17 MONO OUT – The Left and Right main Mix outputs are

summed together to a monaural signal and sent out this con

nector.

18 2 TRACK INPUTS & OUTPUTS – Connect a DAT,

Cassette, Mini Disk or Hard Disk Recording system.

19 MONO OUT LEVEL – Used to set the volume of the

MONO mix.

20 HDM ( Hard Disk Mode) - Switch configures the mixer for

recording and overdubbing on a computer based hard

disk recording system.

21 PHANTOM – Indicates that the 48 Volt Phantom Power is

on.

22 POWER – Indicates the MDR6 is powered up.

23 OUTPUT METER - Five segment display with VU

ballistics indicates main Mix level.

24 MIX FADERS – Used to control the overall volume of

the Left and Right main Mix outputs.

25 2TK LEVEL - Level control used to mix the 2 track input

with the mix from the channel inputs.

26 AUX RETURN – Used to mix in level of the effects return.

27 HEADPHONE JACK – Connect stereo headphones here.

28 C ROOM/HEADPHONE – Adjusts the volume of the con

trol speakers or headphones.

29 2TRACK/MIX – Switches between the main Mix and the

2 Track in the Control Room output.

30 BALANCE – Adjusts the relative loudness of the

signal sent to the Left and Right mix outputs.

REAR PANEL

A AC ADAPTOR INLET – Connect External AC power sup-

ply here.

B POWER – Switches on the MDR6’s main power.

C PHANTOM – Engages the 48-Volt Phantom power sup

ply to microphone pre- amps.

Front and Rear Panel Layout

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson MDR6 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info