629784
12
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
10
Setting up your PS10, PB10, or PB10Pro is a simple procedure which takes only a few
minutes:
1. Remove all packing materials (save them in case of need for future service) and
install the unit in a standard 19” rack. We recommend that the PB10 and PB10Pro
be placed in the top slot so that its slide-out LED lamps can be used to illuminate
the entire rack of equipment below.
2. Connect the PS10, PB10, or PB10Pro to any standard grounded AC outlet. If you
are using a PB10Pro, the front-panel voltmeter and ammeter will show you the
incoming electrical voltage and current draw of connected equipment.
3. Connect the AC cables of your rack equipment to the rear-panel switched AC
outlets, using the included IEC cables.
4. Make sure all connected equipment is switched off, then press the front panel
Outlets switch so that its status light is lit red. This activates all rear panel
switched outlets.
5. Turn on all connected equipment, one at a time. If the total load exceeds 10
amps, the front-panel circuit breaker will trip. To reset it, unplug one or more
devices, then press in the front panel circuit breaker.
6. You can also use the unswitched front panel convenience outlet for additional
temporary power needs (such as connecting a guitar amplifier, soldering iron,
etc.). This outlet is fully operational whenever the PS10, PB10, or PB10Pro is
plugged into an AC source, regardless of the position of the front panel Outlets
switch. The front panel circuit breaker affects this outlet as well as all rear-panel
switched outlets.
7. (PB10 and PB10Pro only) - To illuminate the equipment in your rack, gently pull
the front-panel slide-out cylinders out towards you. The lamps will switch on
automatically .
8. You can illuminate the back of your rack by connecting the included USB
gooseneck LED light to the rear panel USB power socket.
Setting Up and Using Your PowerStrip or PowerBrite
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Samson PB10 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info