MINI CAMERA User Guide
12
MINI CAMERA User Guide
13
MINI CAMERA User Guide
14
MINI CAMERA User Guide
15
MINI CAMERA User Guide
11
MINI CAMERA User Guide
10
MINI CAMERA User Guide
9
MINI CAMERA User Guide
8
• When installing the camera on a ceiling, note that not to damage or squeeze the cables.
Notes
Connecting to Power
•
Connect the adapter to the power input connector as shown in the figure below.
Use a DC 12V. (The Adapter is not provided with the Dome Camera.)
MINI Camera
Adapter (not provided)
Power Input Connector
MINI Camera
Connection to Monitor
•
As a connecting method varies according to instruments, refer to the manual supplied
with the instrument.
• Connect the cable after power is turned off.
Resistance of copper wire [at 20C
º(68ºF)]
• As the voltage drop according to the length of the cable in the above table,
a camera may malfunction if there is an excessively long cable run.
* Voltage for camera operation: 12V DC ±10%
* Voltage drops in the above table are variable according to types of cable manufacturer.
For DC Power Type
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
• In case of adjusting the tilting, do not take the lens for preventing hysical shocks. Please take the Tilt Base.
• This dome camera is to be installed on the ceiling by factory default.
Notes
Panning & Tilting Control
You can adjust the Panning and Tilting angle freely. (Panning angle: 0º-60º, Tilting
angle: 0º~180º)
1)
Adjustment Panning angle: After attaching the dome camera to a ceiling, adjust the
panning angle for better monitoring area by rotating the Pan Base. The panning angle
can be adjusted by 0º~60º.
2) Adjustment Tilting angle: After attaching the dome camera to a ceiling, adjust the
tilting angle for better monitoring area by rotating the Tilt Base. The tilting angle
can be adjusted from 0º to 180º freely. (based the ceiling surface)
Pan Base
You can rotate the lens by
0º~60º
Tilt Base
You can adjust up and down
the camera (0º~180º).
Pan Base
Holding Screw
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem, contact an authorized
technician.
◾ The image on the screen is dim.
• Check if the lens are stained. If dirty, clean the lens with soft, clean cloth.
•
The image is dimmer at night than daytime. If the focus is not right, adjust it at daytime.
◾ The contrast on the screen is too weak.
• Adjust the contrast feature of the monitor.
• If the camera is exposed under too strong light, change the camera position.
• Adjust the lens BACK FOCUS again.
◾ The camera is not work properly, and the surface of the camera case is hot.
• Check that you have connected the camera to a proper power (DC 12V).
Monitor
BNC
Built-in functions of the SCB-2010 Camera include the following
✽ If you need to control OSD menu, It needs control KEY or coaxial controller.
Camera Operation
Troubleshooting
Dimension
SpecificationSpecification
Copper wire size (AWG)
#24(0.22mm
2
) #22(0.33mm
2
) #20(0.52mm
2
) #18(0.83mm
2
)
Resistance ( Ω / m) 0.078 0.050 0.030 0.018
Voltage Drop (V/m) 0.028 0.018 0.011 0.006
Auto Functions Setting Descriptions
Electronic Shutter
Speed
ESC
The shutter is controlled according to the
brightness of screen by automatically.
WHITE BALANCE ATW
It can be used within the color temperature
range 1,700K ~ 11,000K.
BACKLIGHT OFF
It helps view a desired area of picture at the
backlight condition.
GAIN CONTROL HIGH
The gain increases or decreases within the
range of 6dB~34dB.
SSNR3
(Noise Reduction)
ON
There is sufficient reduction in noise levels
without causing much ghost imaging.
SENS-UP AUTO
It helps maintain a bright, clear screen image by
automatically detecting changes in the level in
low light levels without causing much ghost
imaging.
SHARPNESS ON
The outline of the video image becomes cleaner
and more distinctive.
LENS SHADE ON It helps correct shading of Lens.
SCB-2010N SCB-2010P
ELECTRICAL
Input Voltage DC 12V ±10%
Power Consumption Max 1.8W
VIDEO
Imaging Device 1/3 inch, Sony Super HAD CCD II
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
Scanning System 2:1 Interlace
Synchronization Internal/Line lock
Frequency H : 15.734KHz V : 59.94Hz H: 15.625KHz V : 50.00Hz
Horizontal
Resolution
color: 600TVL
Min. Illumination color: 0.04 Lux (50 IRE@F1.2, Sens-up 2x)
S / N (Y signal) 52dB (Weight On, AGC Off)
Video Output CVBS : 1.0Vp-p, 75Ω composite
LENS
Focal Length 3mm
Angular Field of View
H : 95°, V : 71°
Max. Aperture Ratio
F2.0
Min. Object Distance
0.4m
PAN / TILT
Pan / Tilt Range 0° ~ 60° / 0° ~ 180°
OPERATIONAL
Shutter Mode ESC, A.FLK, Manual
Lens Shade On / Off (Level adjustable)
SSDR On / Off (Level adjustable)
※
The specification for this product may change without prior notice for product improvement.
Backlight
Compensation
USER BLC / HLC / OFF
Day & Night COLOR / BW / AUTO (Electric Type)
Gain Control Low / High / Off
White Balance ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K)
SENS-UP Auto / Off (Selectable x2 ~ x512)
Motion Detection On / Off (8 Programmable zones)
Privacy Masking On / Off (12 Programmable zones)
SSNR3 On / Off (Level adjustable)
Digital Zoom On / Off (x1 ~ x16)
DIS On / Off
Camera Title On / Off (Displayed 15 Characters)
Sharpness On / Off (Level adjustable)
Flip / Mirror
On / Off
Communication Coaxial (Pelco Coaxitron)
Electronic Shutter Speed
1/60 ~ 1/120,000 sec 1/50 ~ 1/120,000 sec
On Screen Display
English, Korean, Japanese, Spanish,
French, Portuguese
English, Chinese, German, Italian,
French, Spanish, Russian, Czech, Polish,
Romanian, Serbian, Swedish, Danish,
Turkish, Portuguese
ENVIRONMENTAL
Operating Temperature /
Humidity
-10°C ~ +50°C / Less than 90% RH
MECHANICAL
Color/Material Ivory/Plastic
Dimension(W x H x D)
52 x 52 x 40.4mm(without bracket)
52 x 52 x 81.4mm(with bracket)
Weight
95g (with bracket)
BNC-Power Cable
UNIT: mm(inch)
