Bedienungsanleitung Sangean ATS404 (Seite 7 von 10) (Englisch)

110381

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

3.Press the numbered button corresponding to the preset memory location for the

required station .The radio will instantly tune to the station and the display will show its

frequency and memory location.

Select Short Wave Meter band

1.Turn on the radio by pressing the POWER on/off button.

2.Press BAND button to select the SW waveband .

3.Press SW SELECT button to select the required SW meter band ,display will appear

frequency and SW meter band it belongs to .This radio covers SW 120 to 11 meter band.

APS (Auto Preset System)

This radio provides an easy to use feature called APS (Auto Preset System) which operated

on FM and MW bands.

1.Turn on the radio by pressing the POWER on /off button.

2.Press BAND button to select the required waveband.

3.Press Tuning UP and DOWN button at the same time for more than 2 seconds.

The radio will beep and the display will flash APS indicating the radio in APS mode.

4.The radio will then scan from the lowest frequency on the selected band, automatically

storing stations in preset memory based on signal strength order.

5.After APS is completed, a beep will be heard, The display will show MEMO 1 and the

station with the strongest signal for your area will be selected.

6.IF during APS operation ,on stations are found the display show 87.50 MHz on FM band

or 520 kHz on MW band.

Note: 1. The maximum number of preset on MW band is 9 and FM band is 18.if during APS

operation more than 9(WM) OR 18(FM)are found only 9 or 18 strongest stations

will be stored in the preset memories.

2.The SW band has no APS function.

3.All previously stored preset stations will be erased when APS operation commences.

4.APS operation can be cancelled by pressing the POWER on/off button.

Memory Scan

This radios provides a feature called Memory Scan which when activated will scan the

preset memories.

1.Turn on the radio by pressing the POWER button .Select the required waveband .

2.Push the MEMO SCAN button ,the radio will scan each preset memory in turn-pause for

7seconds on each memory before continuing on to the next memory .When the required

preset station is reached, press any button to stop memory scan.

Setting the alarm (standby)

The alarm can be set with the power on or off.

If the radio is switched on, press the DISPLAY button to display the time.

Radio alarm

1.Press ALARM button, display ALARM will flash and show the last alarm time set, press

the numbered button to set the alarm on time and press ALARM button again to set radio

alarm, display will display “ ALARM ” (radio alarm), during the flashing, press ENTER

to complete.

2.To verify the alarm time, press ALARM button to display the alarm time followed by the

ENTER button to return to real time mode.

3.To cancel the alarm, press ALARM button, display will show previous alarm set status,

press.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sangean ATS404 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sangean ATS404

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info