Bedienungsanleitung Satel AMD-103 (Seite 2 von 4) (Englisch)

699877

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

2 AMD-103 SATEL

Every 15 minutes, the detector sends a transmission with information on the current status of

the reed switch, tamper contact and battery. Periodic transmissions are used to monitor

presence and operation of the magnetic contact.

Note: In the case of the AMD-103 magnetic contact, the presence check is performed in

a different way than for the other ABAX system devices. If the value programmed for

the F

ILTER

parameter differs from 0, the lack of presence will be reported if no

transmission from the detector is received within one hour.

The LED is only working in the test mode:

 it is lit for 80 milliseconds, when the test transmission is being sent;

 it is lit for 2 seconds in the event of alarm.

The test mode is turned on for 20 minutes after inserting the batteries or opening the tamper

contact.

The detector checks the battery status. When the voltage is lower than 2.6 V, the low-battery

information is sent during each transmission.

4. Installation

There is a danger of battery explosion when using a different battery than

recommended by the manufacturer, or handling the battery improperly.

Be particularly careful during installation and replacement of the battery. The

manufacturer is not liable for the consequences of incorrect installation of the

battery.

The used batteries must not be discarded, but should be disposed of in

accordance with the existing rules for environment protection.

The device is designed for indoor installation. The detector should be mounted on a fixed

surface (e.g. window or door frame), and the magnet on a movable surface (e.g. window or

door). Mounting the magnetic contact on ferromagnetic surfaces and/or near to strong

magnetic and electrical fields is not advisable, because it can result in malfunctioning of the

device.

Special designation on the detector enclosure indicates the side on which the magnets

should be installed (Fig. 6).

1. Open the detector enclosure (Fig. 2).

2. Install the battery and add the device to the wireless system (see the ACU-100 / ACU-250 /

ACU-120 / ACU-270 controller manual, installer manuals for INTEGRA 128-WRL or

VERSA control panels).

3. Close the detector enclosure (the tamper contact must be pressed down by the base

element).

4. Fasten the detector temporarily at the place of its future installation.

5. Move the magnet away from the detector. The detector will send information on the alarm,

which will allow you to check the level of signal received from the detector by the

ACU-100 / ACU-250 / ACU-120 / ACU-270 controller or the INTEGRA 128-WRL control

panel. If necessary, select another place for installation, to ensure adequate

communication quality.

6. Open the detector enclosure (Fig. 2).

7. Using wall plugs (screw anchors) and screws, fasten the enclosure base to the mounting

surface (Fig. 3).

8. Close the detector enclosure (the tamper contact must be pressed down by the base

element).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel AMD-103 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel AMD-103

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info