Bedienungsanleitung Satel VERSA 10 (Seite 30 von 32) (Englisch)

699459

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

28 VERSA SATEL

3.19.2 Output test

The function makes it possible to check proper functioning of the system outputs as well as

devices connected to them.

You can always test 12 outputs.

1. Enter the user menu and press in turn . The keypad indicates the

output status by means of LEDs numbered from 1 to 12 (LED OFF – the output is

deactivated; LED ON – the output is activated). The blinking LED means that the cursor is

there. The and keys allow you to move the cursor.

2. Press to activate the output, or press to deactivate the output.

3. Press

to terminate the function.

3.19.3 Checking the level / quality of radio signal

The function allows you to check:

 the quality of radio signal received by the controller from 433 MHz wireless detectors (if the

VERSA-MCU controller is connected to the control panel),

 the level of radio signal received by the controller from ABAX wireless devices (if the

ABAX system controller is connected to the control panel).

Enter the user menu and press in turn

. The signal level / quality is

illustrated by LEDs designated by numbers:

 1-15 – wireless devices assigned to zones from 16 to 30,

 16-30 – wireless devices assigned to zones from 1 to 15.

The more LEDs are ON, the better is the signal level / quality. When all LEDs are ON, the

signal level / quality is 100%.

The device can be identified by blinking of the LED designated by the number of zone to

which the device is assigned.

You can scroll through the list by using the arrow keys.

3.19.4 Starting the manual test transmission

Enter the user menu and press in turn . A “Manual reporting test” event will

be saved to the control panel memory. The event code will be sent to the monitoring station.

3.19.5 Checking the current supply voltage in modules

Not all modules provide information on the current voltage.

Enter the user menu and press in turn . Information on the supply voltage

of the lowest address module will be displayed. Blinking of the LED designated by the

number corresponding to the module address number (for address 0, LED 30 is blinking)

enables identification of the module. Depending on the module address, the supply voltage is

illustrated by the LEDs numbered 1-15 (address 0 and addresses from 16 to 21) or 16-30

(addresses from 1 to 15). To determine the voltage, sum up the number of LEDs which are lit

(a single LED corresponds to the voltage of 1 V). You can scroll through the list by using the

arrow keys.

3.19.6 Outputs reset

Use the function to:

 deactivate 5. “DURESS” ALARM, 14. CHIME or 15. CONTROLLED function outputs (if the cut-

off time equal to 0 is programmed by the installer for such an output, the output can only

be deactivated in this manner),

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA 10 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info