563702
11
Zoom out
Zoom in
Vorherige Seite
1/15
Nächste Seite
11
FLUE INSTALLATION
Flue option Cutting length (mm) Comments
outer pipe inner pipe
Side flue left e + a - 1479 e + a - 1479 maximum
dimension "X" without
extension 739 mm
Side flue right e + a - 1479 e + a - 1479 maximum
dimension "X" without
extension 739 mm
Table 3
RTSNQOP U
V
Pho 088
Diagram 12
Pho 087
165
182
80
L
Restrictor a
Spacer b
Hab 243
Extended flue
The horizontal flue is extended by using one or more
of the 1000 mm extension pipes, Saunier Duval part
number 85091. These are connected together by
push fit type joints, clamps and seals.
Calculation of flue cutting lengths for extended flue
Using the correct number of extension kits as ta-
ble 2, measure dimensions a and e, see diagram
9. Cut both the inner and outer pipe to the dimen-
sions given in table 3.
Important: All cutting lengths should be measured
from the push fit end of the extension pipe. Do not
leave any burrs or sharp edges on the cut ends of
the pipes.
Installation of flue assembly
Fit rubber sealing collar (P) into groove at the
outer end of pipe (N), see diagram 11.
Fit outer pipe (N) into wall with groove to the
outside.
Pull pipe inwards to bring rubber sealing collar
hard up against external wall, see diagram12.
Fit internal plastic flange (Q) onto outer pipe.
Push along the pipe until engaged against inter-
nal wall.
From inside, insert inner pipe (O) into outer pipe.
Fit both 'O' rings (T) into the flue elbow (V), one
at the inlet, one at the outlet. By necessity, they
are a loose fit, apply a small amount of silicone
grease to each 'O' ring when fitting.
Slacken the two screws and fit the clamp and
seal (R) onto the elbow.
Take hold of the inner flue and push gently onto
the elbow outlet taking care not to tear the 'O' ring.
Important: If the flue has been cut, ensure that there
are no burrs that could damage the 'O' ring.
Push the elbow clamp and seal over the outer
flue.
For flue systems less than 1 m long, leave the cup
restrictor (a) fitted in the boiler flue outlet, see dia-
gram 13.
Diagram 11
Remove the backing from the self adhesive gas-
ket (S) and carefully fit gasket to base of flue el-
bow.
Fit spacer (b) onto underside of elbow, fit elbow
onto boiler and secure with the four screws (U).
Diagram 13
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Saunier Duval Thelia 30 e wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info