781646
14
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
14 GB
Tool removal (Fig. 4)
Pull back and hold the locking sleeve (2) and remove
the tool.
Dust collection device (Fig. 5)
Slide the dust collection device (a) over the drill bit be-
fore carrying out any hammer drilling vertically above
your head.
Starting up
Important.
To prevent all danger, the machine must only be
held using the two handles. Otherwise there may
be a risk of suffering an electric shock if you drill
into cables.
Switching on and off (Fig. 1)
To switch on: Press the control switch (4).
To switch off: Release the control switch (4).
Setting the operating mode (Fig.6)
The operating mode of the power tool is selected with
the mode selector switch
Note: Change the operating mode only when the
machine is switched off! Otherwise, the machine can
be damaged.
– Turn the mode selector switch to the requested
position.
Position for hammer drilling (A): When the drilling
tool does not immediately rotate upon switching on,
allow the machine to run slowly until the drilling tool
rotates.
Vario-Lock (B) position for adjustment of the
chiselling position
Position for chiselling (C)
Important.
Only low pressure is required for hammer dril-
ling. Excessive pressure will exert an unnecessary
force on the motor. Check the drill bits at regular
intervals. Sharpen or replace blunt drill bits.
Replacing the power cable
If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its aftersales
service or similarly trained personnel to avoid danger.
Cleaning and maintenance
Always pull out the mains power plug before starting
any cleaning work.
Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible. Wipe
the equipment with a clean cloth or blow it with com-
pressed air at low pressure.
We recommend that you clean the device immediately
each time you have nished using it.
Clean the equipment regularly with a moist cloth and
some soft soap. Do not use cleaning agents or sol-
vents; these could attack the plastic parts of the equip-
ment. Ensure that no water can seep into the device.
Carbon brushes
In case of excessive sparking, have the carbon brushes
checked only by a qualied electrician. Important! The
carbon brushes should not be replaced by anyone but
a qualied electrician
Maintenance
There are no parts inside the equipment which require
additional maintenance.
Disposal and recycling
The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material and
can therefore be reused or can be returned to the raw
material system.
The unit and its accessories are made of various types
of material, such as metal and plastic. Defective com-
ponents must be disposed of as special waste. Ask your
dealer or your local council.
Storage
Store the equipment and accessories out of children’s
reach in a dark and dry place at above freezing tempe-
rature. The ideal storage temperature is between 5 and
30 °C. Store the electric tool in its original packaging.
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Scheppach DH1200MAX wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info