Bedienungsanleitung Scheppach DP19Vario (Seite 24 von 148) (Deutsch, Englisch, Französisch, Italienisch, Polnisch)

781654

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

24 | GB

Material mixtures are particularly dangerous. Light

metal dust can burn or explode.

• Set the correct speed before starting work. The

speed must be appropriate for the drill diam-

eter and the material to be drilled. At an incor-

rectly set speed the bit may get jammed in the

workpiece.

• Only when the device is turned on should the

bit be moved against the work piece. Otherwise

there is a danger that the bit will get jammed in the

workpiece and the workpiece will rotate with the

bit. This can lead to injuries.

• Do not put your hands in the area of the drill

while the power tool is running. Upon contact

with the bit is a risk of injury.

• Never remove drilling chips from the drilling

area while the power tool is running. Always

put the drive mechanism in the standby position

rst and then turn on the power tool.

• Do not remove accumulated drill chips with

your bare hands. There is a risk of injury due to

hot and sharp metal shavings in particular.

• Break up long drilling chips by interrupting the

drilling operation with a short backward rota-

tion of the rotary wheel. Long drilling chips may

cause injury.

• Keep handles dry, clean and free from oil and

grease. Greasy, oily handles are slippery and lead

to loss of control.

• Use clamps to hold the workpiece in place. Do

not work on any workpieces that are too small

for clamping. If you hold the workpiece by hand,

you cannot hold it sufciently tightly against rota-

tion and may hurt yourself.

• Switch the power tool off immediately if the bit

jams. The bit jams when:

- the power tool is overloaded or

- the workpiece to be machined is jammed.

• Do not touch the bit after working before it has

cooled down. The bit is very hot during use.

• Inspect the cable regularly and have a dam-

aged cable repaired only by an authorised cus-

tomer service centre. Replace damaged exten-

sion cables. This will ensure that the power tool

remains safe.

• Store unused power tools in a safe place. The

storage place should be dry and lockable. This

prevents the power tool from being damaged as

a result of being stored or operated by inexperi-

enced people.

• Never leave the tool before it has come to a

complete standstill. After running bits can cause

injury.

• Do not use the power tool with a damaged ca-

ble. Do not touch the damaged cable and pull

the mains plug if the cable is damaged while

working. Damaged cables increase the risk of

electric shock.

• Use extension cables for outdoors

- Only use approved and appropriately identied ex-

tension cables for use outdoors.

• Remain attentive

- Pay attention to what you are doing. Remain sen-

sible when working. Do not use the electric tool

when you are distracted.

• Check the electric tool for potential damage

- Protective devices or other parts with minor dam-

age must be carefully inspected to ensure that they

function correctly and as intended prior to contin-

ued use of the electric tool.

- Check whether the moving parts function faultless-

ly and do not jam or whether parts are damaged.

All parts must be correctly mounted and all condi-

tions must be fullled to ensure fault-free operation

of the electric tool.

- Damaged safety equipment and parts must be re-

paired properly or replaced by an authorised spe-

cialist workshop unless otherwise indicated in the

instructions.

- Damaged switches must be replaced at a customer

service workshop.

- Do not use any electric tool on which the switch

cannot be switched on and off.

• ATTENTION!

- The use of other insertion tools and other acces-

sories can entail a danger of injury.

• Have your electric tool repaired by a qualied

electrician

- This power tool complies with the relevant safe-

ty regulations. Repairs may only be performed by

a qualied electrician, using original spare parts;

otherwise accidents involving the user may result.

Warning! This electric tool generates an electromag-

netic eld during operation. This eld can impair ac-

tive or passive medical implants under certain condi-

tions. In order to prevent the risk of serious or deadly

injuries, we recommend that persons with medical

implants consult with their physician and the manu-

facturer of the medical implant prior to operating the

electric tool.

Service:

• Only have your electric tool repaired by quali-

ed specialists and only with original spare

parts. This will ensure that the power tool remains

safe.

Safety Instructions for Box Column Drills

• Never make the warning labels on the power

tool illegible.

• Attach the power tool to a solid, at and hori-

zontal surface. If the power tool can slip or wob-

ble, the bit may not be guided smoothly and safely.

• Keep the work area clean except for the

workpiece to be machined. Sharp-edged

drilling chips and objects can cause injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DP19Vario Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info