Bedienungsanleitung Scheppach HF3000 (Seite 5 von 28) (Alle Sprachen)

782058

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

6 deutsch english 7

Manufacturer:

Scheppach Maschinenfabrik GmbH & Co. KG

Günzburger Straße 69

D-89335 Ichenhausen / FRG

Dear customer,

we wish you a lot of enjoyment and success while working

with your new scheppach unit.

We recommend:

Read through the entire text before assembling and

beginning operation.

General Notes

• Design and execution subject to change without notice.

• Check all parts for possible shipping damage

after unpacking. The shipper must be informed

immediately if a complaint is to be led.

• Claims made at later date will not be processed.

• Check the delivery to make sure it is complete.

• Familiarize yourself with the unit by reading the

instructions before operating.

• Use only original scheppach parts for accessories as well

as for spare and expendable parts.

• When ordering, state our item numbers as well as type

and model year of the unit.

Notes on safety

• Observe the safety notes of your scheppach machine the

pusher slide is to be mounted on.

• Be sure to use tools safely and precisely when

operating.

• Safety devices may not be removed.

Assembly

For packaging reasons, your scheppach pusher slide is not

completely assembled.

tku/ts 315 GT, Fig. A1

• Attach the mounting plates to the front and rear of the

table.

2 hex bolts each M8 x 20

2 washers each 8 in diameter.

• Hex bolts should be hand-tightened only.

hf 3000/tfe 30, Fig. A2

• Attach the mounting plates to the front and rear of the

table.

2 hex bolts each M8 x 20

2 washers each 8 in diameter.

• Hex bolts should be hand-tightened only.

• Screw in adjusting screw (1). The inner adjusting screw

rests on the shank of the screw bracket on table tops

without a rolled lower edge.

Guide tube Fig. B

• Insert the guide tube with the fastening arms, press on

and tighten the retaining plate (1).

1 washer 8 in diameter

1 hex nut M8 self-tightening

• 0.5 mm play must remain between the fastening arms

and the retaining plate.

• Fasten the fastening arms using a wing nut M8 and a

washer 8 in diameter on top of the retaining plate.

Adjust, Fig C

• Allow the stop on the guide tube to catch. Pull out and

turn.

• Push the empty slide table onto the guide tube and allow

the stop to catch again.

Adjust, Fig D

• Align the slide table. Use the stop track as a ruler. The

slide table must move parallel to saw or millig table and

at the same height.

• Check repeatedly and then tighten the hex bolts of the

mounting plates.

Adjust hf 3000/tfe 30

• Bring the slide table to the same level using the adjusting

screws on the screw brackets (Fig. A2) on the front and

rear side of the table.

• Check repeatedly and then tighten the hex bolts of the

mounting plates.

Assembling the switch on tk, tkh, tku, Fig. A1

• Screw switch to switch plate. Screw the unit onto the

front mounting plate

2 cheese head screws M5 x 15

2 large washers A 5,3

2 hex. nuts M5

Final assembly tk, tkh, tku, ts315 GT, Fig. E

(1) Stop tube

(2) Adjusting bolt

(3) Stop track

• Insert stop tube (1) in the pivoting drill hole of the slide

table.

• Insert carriage bolt M8 x 65 from above and tighten with

washer by hand.

79510000 79540000

Delivery Package

Pusher table

assembly

Pusher table

assembly

Guide tube assembly Guide tube assembly

Front mounting

support assembly

Front mounting

support assembly

Rear mounting

support assembly

Rear mounting

support assembly

Stop tube assembly Stop tube assembly

Stop track Stop track

Accessory bag Clamping device

Operating

instructions Accessory bag

Bearing strip

Operating

instructions

Technical Data

Work piece

width max.

(mm) between

tool and stop

at 90° position

550 500

Pivoting area,

stop track 2 x 45 ° 2 x 45°

Fixed anchor

point 15° each 15° each

Max. clamping

range of the

clamping

device (mm)

– 105

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HF3000 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scheppach HF3000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info