Bedienungsanleitung Scott Plasma 5 - 2018 (Seite 8 von 13) (Englisch)

779966

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

ENGLISHENGLISH

SEATPOST

Saddle assembly:

•IMPORTANT

before assembling the saddle, make sure the seatpost saddle rail clamps

(524/525) are compatible with your saddle rails!

Measure your saddle rails height and width (HxW). Ritchey WCS Carbon One-Bolt

Saddle Rail Clamp outer-pieces specifications should be compatible with your

saddle rails.

If the saddle rails dimensions you measured are different from the saddle clamps

specifications, purchase the required saddle rail clamps parts at your retailer’s, the

following dimensions are available: 7x7mm, 8x8.5mm or 7x9.6mm.

Set the right saddle tilt and position the saddle rails so that the saddle rail clamps

are in the middle of the usable rail clamping area. Tighten the M6 screw (527) to the

specified torque (T13) to assemble the saddle.

Use the seatpost adjustment barrel to adjust your BB-Saddle horizontal offset.

Once the right offset is set, tighten the two M5 barrel screws (521) to the specified

torque (T12), in some cases, you will need to remove the saddle to access the two M5

barrel screws.

Battery/Seatpost assembly:

•IMPORTANT

for electronic shifting assemble the seatpost battery mount parts (530) together so

that their concave surfaces are facing.

Put the O-ring part (531) into the groove and put the rubber part (532) in between

the two battery mount parts (530) so that one of its shoulders sticks out of the parts.

Assemble the battery mount parts (530) with the seatpost (501) by pinching the

upper end of the battery mounts and so that their pins coincide with the seatpost

low end holes.

Release the battery mounts once the pins are in position and pull apart the battery

mounts parts to leave enough space for the battery (999) to be mounted.

Once the battery mounts ribs are positioned into the battery groove, release the

battery mounts and connect the battery to the battery wire sticking out of the frame

seat tube.

Seatpost assembly:

•IMPORTANT

before assembling the seatpost into the frame, make sure the rear side of the

seatpost (side where head is longer) is at the rear end of the frame.

Push gently the seatpost into the frame.

•IMPORTANT

For electronic shifting: make sure the battery does not get stuck into the frame,

once the desired seatpost height is achieved pre-assemble the seatpost wedge:

position the upper wedge part (505) over the mid wedge part (504) and the low

wedge threaded part (503) below the mid wedge part.

Position the M6 wedge screw (506) into the assembly head up and pre-tighten it

over 3 turns. Position the wedge assembly into the seat tube insert in front of the

seat tube, its concave face should correspond to the seatpost front surface. Tighten

the M6 screw to the specified torque (T11) while making sure the upper surface of the

wedge coincides with the upper surface of the top tube.

Seatpost Plasma 4/5 SCOTT part number: 239318

Seat Clamp Plasma 4/5 SCOTT part number: 239544

15 |

BIKE USER MANUAL | PLASMA 5PLASMA 5 | BIKE USER MANUAL

| 14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scott Plasma 5 - 2018 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scott Plasma 5 - 2018

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info