779966
11
Zoom out
Zoom in
Vorherige Seite
1/13
Nächste Seite
ENGLISHENGLISH
Frame/Rear Brake assembly:
Advisory: The SCOTT Plasma is only compatible with SHIMANO direct mount
compatible brake calipers. The recommended rear brake caliper for the
SCOTT Plasma 5 is the SHIMANO Dura-Ace BR-9010. Only this brake model
is compatible with the rear aero brake cover (410) delivered with the SCOTT
Plasma 5 frameset.
To assemble the SHIMANO Dura-Ace BR-9010 rear brake caliper on the frame, please
refer to the SHIMANO assembly instructions leaflet delivered with the bike or calipers.
BRAKE COVERS
Front brake cover:
assemble front brake cover screw (403) with the front brake cover part (401) and
secure its position with the front brake cover O-ring (404) by positioning the O-ring
over the screw’s threads in order to leave 3mm of free threads at the end of the screw.
Position the front brake cover pin (402) into the stem pinhole located on the low part
of the stem (301) and position the front brake cover over the front brake and secure
it into position by tightening the front brake cover screw to the specified torque (T8).
Advisory: There are 4 front brake covers (401) available in S/M/L/XL each
corresponding to the frame size.
Front brake covers (S-XL) SCOTT part number: 239182
Rear brake cover:
position the rear brake cover clips into the exit hole on the underside of the
downtube in front of the bottom bracket,
Advisory: make sure the cable housings and wires run in between the two clips.
Rotate the rear brake cover until it enters in contact with the brake caliper lever arms,
gently pull the rear cover left side to introduce the brake caliper lever arms into the
rear brake cover left opening.
Keep on rotating the rear brake cover until it reaches its final position, make sure the
two chainstay threaded inserts are visible from the rear brake cover holes.
Push the rear brake cover frontwards to ensure the clips are engaged into the
frame, position and tighten the two M4 rear brake cover screws (411) to the specified
torque (T9).
Rear brake cover SCOTT part number: 239183
21 |
BIKE USER MANUAL | PLASMA 5PLASMA 5 | BIKE USER MANUAL
| 20
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Scott Plasma 5 - 2018 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Scott Plasma 5 - 2018

Scott Plasma 5 - 2018 Bedienungsanleitung - Deutsch - 13 seiten

Scott Plasma 5 - 2018 Bedienungsanleitung - Französisch - 13 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info