3.Press “A” to set the digits. The digits move quickly if the button is kept pressed.
4.Press “B” to return to the TIME/CALENDAR display.
Before setting the time/calendar or ID No., be sure to reset the stopwatch to “00.” The time/calendar and ID No. can be set only when the stopwatch is reset.
1.Press “D” to show the TIME/CALENDAR display, and then press “B.” SECOND digits flash. Press “A” to reset the SECOND to “00.”
2.Press “B” repeatedly to select the digits (flashing) to be adjusted in the following order.
Hour
ID No.
TIME/CALENDAR display indicator
MonthYear
Date
Seconds
A
B
D
Minutes
Notes:
1.The calendar automatically adjusts for odd and even months including February of leap years from 2006 to 2055.
2.When the SECOND reads any number from “30” to “59” and “A” is pressed, one minute is added.
3.The time is displayed in the 24-hour indication.
4.The ID No. can be set in two digits from “01” to “99”. When “OFF” is displayed, it indicates that no ID No. is set.
The contrast of the liquid crystal display can be adjusted in 10 steps from level “1” to “10.”
1.Press “C” in the TIME/CALENDAR display to show the CONTRAST ADJUSTMENT display.
2.Press “A” or “B” repeatedly to adjust the contrast. The display becomes darker by pressing “A”
and lighter by pressing “B.”
3.Press “C” or “D” to return to the TIME/CALENDAR display.
Contrast
level
BA
C
D
Block memory mode Single memory mode
BLOCK markChange of memory mode will delete all the
previously stored data.
CAUTION
5.To change the memory mode, press and hold "A" for 1.5 seconds.
When "OFF" is displayed above "BLOCK," the stopwatch is in the single memory mode, which is the default setting.
When "ON" is displayed above "BLOCK" and the BLOCK mark appears at the bottom right, the stopwatch is in the block memory mode, which is designed for
professional level use.
Refer to MEMORY RECALL FUNCTION---BLOCK MEMORY MODE on page 3.
STOPWATCH
Before using the stopwatch, be sure to reset the digits to “00.”
When the stopwatch is stopped, press “B.”
When the stopwatch is counting, press “A” and then press “B.”
1.STANDARD MEASUREMENT
ABA
STARTSTOPRESET
2.ACCUMULATED ELAPSED TIME MEASUREMENT
AAA
STARTSTOPRESTART
A
STOP
B
RESET
*Restarting and stopping the stopwatch can be repeated by pressing “A.”
Press “D” to show the STOPWATCH 1 (Accumulated elapsed time) display.
Press “D” to show the STOPWATCH 1 (Accumulated elapsed time) display.
•Up to 300 lap/split time data can be stored in memory and recalled during or after measurement.
•The stopwatch can measure and display the lap/split time that exceeds its limit of 300, but it cannot store the data in memory for the 301st measurement
data and afterward.
*When a new measurement is commenced while the stopwatch is in the single memory mode, the lap/split time data obtained from the previous measurement will be automatically deleted.
•For professional level use, the default single memory mode can be changed to the block memory mode, in which commencement of a new measurement
will not erase the previous measurement data. The block memory mode is useful for saving records or comparing data.
Refer to MEMORY RECALL FUNCTION---BLOCK MEMORY MODE on page 3.
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Seiko S141 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.