759223

Sencor SCF 4201 Seite 7

7
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
- 7 - 08/2019
Copyright © 2019, Fast ČR, a.s.
EN Convection heater
User'smanual
■ Prior to using this appliance, please read the user’smanual thoroughly, even in cases,
when one has already familiarised themselves with previous use of similar types of
appliances. Only use the appliance in the manner described in this user’smanual.
Keep this user’smanual in asafe place where it can be easily retrieved for future use.
■ We recommend saving the original cardboard box, packaging material, purchase
receipt and responsibility statement of the vendor or warranty card for at least the
duration of the legal liability for unsatisfactory performance or quality. In the event
of transportation, we recommend that you pack the appliance in the original box
from the manufacturer.
DESCRIPTION OF THE APPLIANCE
A1 Display
A2 Front panel
A3 Travel wheels
A4 Wall mounting hooks
A5 Main power switch (located on the
side)
A6 Wall mounting set (not shown)
DESCRIPTION OF THE CONTROL PANEL
B1 Button ▲
B2 Button ▼
B3 On/Off button
B4 Timer button
B5 Operating mode selection button
DESCRIPTION OF THE DISPLAY
C1 Child lock icon
C2 °C icon
C3 Timer icon
C4 Heating icon
C5 Temperature or timer display
C6 Anti-frost mode icon
C7 Low heating power mode icon
C7 High heating power mode icon
C9 WiFi icon
DESCRIPTION OF THE REMOTE CONTROL
D1 On/Off button
D2 Operating mode setting button
D3 Temperature setting button
D4 Timer setting button
D5 Plus (+) button
D6 Minus (-) button
BEFORE FIRST USE
■ Before first use, take the appliance and its accessories out of the packaging material
and remove all promotional labels and stickers. Check that neither the appliance nor
any of its parts is damaged.
INSTALLATION
■ The convection heater may be used as amobile heat source (necessary to install
the travel wheels A3) or it may be mounted on awall (travel wheels A3 must be
removed).
Warning:
Before any type of installation, always make sure that the power
plug is disconnected from the power socket.
Installing the travel wheels
■ Put ablanket or another soft underlay on the floor. Then place the convection heater
upside down on to this blanket.
■ On the underside of the convection heater there are three drilled holes on either
side. Align these holes with the holes in the travel wheels A3 and, using the supplied
self-tapping screws, screw them to the underside of the convection heater – see
figure E. Tighten securely. Check that the travel wheels A3 are correctly attached to
the convection heater.
■ Turn the convection heater over and carefully put it down on the travel wheels A3.
Check that the wheels move freely and that they are not blocked in any way.
Wall mounted installation
■ Before mounting the convection heater on awall, it is important that you check that
the installation location has no wires, conduits, pipes, etc. in the wall.
■ Prior to installation, also check that the installation location is at asufficient distance
from the power socket.
Warning:
Only use the supplied set of screws and dowels for the
installation. Under no condition should dowels and screws be
used that have adifferent diameter, different specifications and
which are not approved by the manufacturer as suitable for the
installation of this type of product.
■ Drill two holes of 8mm diameter 40mm deep into the wall as shown in figure F.
■ Insert aplastic dowel into each of the drilled holes. Using ascrewdriver, secure the
screws and leave their heads protruding out approximately 6mm.
■ Put the convection heater on to the wall by sliding the screw heads into the holes
on the hanging hooks A4.
Warning:
The convection heater must be installed at least 15cm above
the ground and 50cm from the ceiling. The convection heater
must always be installed horizontally. Any electrical installations
must be performed by a qualified electrician. The convection
heater must not be installed behind doors or in an outdoor
environment.
USING THE CONVECTION HEATER
Inserting batteries into the remote control
■ Remove the battery compartment cover located on the underside of the remote
control. Insert 2x type AAA 1.5Vbatteries (batteries not included) Ensure that the
correct polarity is adhered to as marked on the bottom of the battery compartment.
Put the cover back on.
■ When replacing batteries, proceed in the same manner. Always replace both
batteries at the same time. Avoid using acombination of new and old batteries or
batteries of various types.
■ If you wish to use the remote control, point it at approximately the level of the
display A1. The maximum signal range is 6m. If the remote control is positioned in
such away that obstacles prevent the transmission of the signal, then the signal may
not be transmitted at all.
Note:
When not using the remote control for an extended period of time,
remove the batteries from the remote control. Never put the batteries
in afire, short circuit them or damage them in any way. Dispose of them
ecologically at the end of their lifetime. Never throw batteries out with
communal waste.
Turning on / off
■ Prior to first use, check that the voltage in your power socket corresponds to the
voltage on the rating label.
■ Insert the power plug into apower socket.
■ Set the main switch A5 to position I(On). Asound is made, the display A1 is lit and
the temperature is shown.
■ To turn on the convection heater, press button B3 on the convection heater or
button D1 on the remote control.
■ The icon of the last set operating mode will be shown on the display A1.
■ When you have finished using it, press the On/Off button B3 on the convection
heater or button D1 on the remote control, and the convection heater will turn itself
off, however, it will remain in stand-by mode. To completely turn off the convection
heater, set the main switch A5 to position 0 (Off) and disconnect the power plug
from the power socket.
Note:
Upon first use or after it has not been used for an extended period of
time, aslight odour may be sensed or asmall amount of smoke may
be emitted from the convection heater. This is completely normal and
will quickly disappear.
Child safety lock
■ The child safety lock function enables the control panel to be locked and prevents
accidental changes to your settings.
■ To turn on the lock function, hold down button ▲ until the child safety lock icon C1
appears on the display A1. All the control buttons will be disabled.
■ To cancel the child safety lock function, hold down button ▲ until the child safety
lock icon C1 disappears from the display A1.
Selecting an operating mode
■ The convection heater has three operating modes: low heating power mode (input
750 W), high heating power mode (input 1500 W) and an Anti-Frost mode.
■ Press button B5 on the convection heater or button D2 on the remote control and
then use buttons ▲/▼ on the convection heater or the +/- buttons on the remote
control to select the required operating mode. The icon of the selected mode (C6, C7
or C8) will be lit on the display A1.
Note:
If also the heating icon C4 is lit on the display A1, this means that the
convection heater is running and is heating to the set temperature. As
soon as the set temperature is reached, the heating icon C4 will turn
off and only the icon of the selected operating mode will remain lit.
Setting the temperature
■ Press button B5 on the convection heater twice or button D3 on the remote control
once. The temperatures digits will start flashing. Set the temperature of the selected
mode using the ▲/▼ buttons on the convection heater or the +/- buttons on the
remote control. Your settings are saved when the temperature digits stop flashing.
You can set the temperature in the range from 5 to 50 °C.
Setting the timer
■ While the convection heater is running, press button B4 on the convection heater or
button D4 on the remote control. The timer icon C3 will be shown on the display A1
and the timer digits “00” will start flashing. Set the convection heater operating time
using the ▲/▼ buttons on the convection heater or the +/- buttons on the remote
control. Your settings are saved when the timer digits stop flashing. The timer icon
C3 will remain lit on the display A1. The set time in hours will start counting down
on the display A1. When the set time has elapsed, the convection heater will turn off
and switch to the stand-by mode.
■ The operating time can be set in the range from 1 to 24 hours.
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sencor SCF 4201 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info