Bedienungsanleitung Sencor SFE 2311 (Seite 5 von 6) (Englisch)

759913

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

03/2017

- 5 -

EN Desktop Fan

User'smanual

■ Prior to using this appliance, please read the user’smanual

thoroughly, even in cases, when one has already familiarised

themselves with previous use of similar types of appliances.

Only use the appliance in the manner described in this

user’smanual. Keep this user’smanual in asafe place where it

can be easily retrieved for future use.

■ We recommend saving the original cardboard box, packaging

material, purchase receipt and responsibility statement of the

vendor or warranty card for at least the duration of the legal

liability for unsatisfactory performance or quality. In the event

of transportation, we recommend that you pack the appliance

in the original box from the manufacturer.

DESCRIPTION OF THE APPLIANCE

A1 Front protective grill

A2 Fan blades with adiameter of 23 cm

A3 Nut for fastening the rear protective grill

A4 Rear protective grill with fastening clamps and acarry

handle

A5 Motor unit shaft

A6 Horizontal oscillation toggle switch

A7 Motor unit with adjustable vertical tilt angle

A8 Panel with control buttons

0 – o, 1 – low speed, 2 – high speed

A9 Base

Note:

The accessories include ascrew and anut for joining the protective

grills.

BEFORE FIRST USE

■ Take the appliance and its accessories out of the packaging

materials. Before disposing of the packaging materials, make

sure that no part of the appliance is missing.

ASSEMBLING AND DISASSEMBLING THE APPLIANCE

■ Insert the control panel A8 from above into the base A9 and

make sure that it is properly seated inside. Grasp the fan under

the motor unit A7 and turn it upside down. Turn the wing nut

located underneath the control panel A8 by 90° to secure the

panel A8 to the base A9 (see g. B). Turn the fan back over to

the operating position and stand it on astraight, clean, dry,

stable and smooth surface.

■ Place the rear protective grill A4 against the front side of the

motor unit A7 so that the handle is above the motor unit A7

and that the alignment tabs on the front side of the motor unit

A7 slide into the respective holes in the rear grill A4. Place the

nut A3 on to the shaft A5 and screw it in clockwise to secure the

rear protective grill A4 to the motor unit A7. Before tightening

the nut A3, make sure that the rear grill A4 has not moved and

that the alignment tabs are still in the respective holes.

■ On to the shaft of the motor unit A5 put on the fan blades A2

so that the shaft A5 properly slides into the centre part of the

fan blades A2. Push the fan blades A2 towards the motor unit

A7 all the way. Now check that the fan blades A2 turn freely.

■ Release the clamps along the perimeter of the rear protective

grill A4. Place the front protective grill A1 against the rear

protective grill A4 so that the front grill A1 fits into the

alignment hook in the bottom part of the rear protective grill

A4 and that the screw holes at the top of both grills are aligned.

Fasten the released clamps along the perimeter of the grills. To

ensure astrong connection of the two grills, into the holes at

the top of the grills it is necessary to screw in the supplied screw

and secure it with the nut.

■ Before putting the fan into operation, check that it is correctly

assembled and that the protective grills are rmly joined.

■ To disassemble, proceed in reverse sequence.

OPERATING THE APPLIANCE

Setting the speed and turning o the fan

■ Locate the fan on an even, dry and smooth surface within reach

of apower socket. Connect the power cord to apower socket.

To set the air ow speed, use the buttons on the control panel

A8. The functions of the control buttons are described below:

0 – turn o the fan;

1– set alow air ow speed;

2– set ahigh air ow speed.

■ When you have nished using the fan, always turn it o and

disconnect it from the power socket.

Setting horizontal oscillation

■ The horizontal oscillation of the motor unit A7 can be set using

the toggle switch A6. To start the horizontal oscillation, push

the toggle switch A6 down. The motor unit A7 will oscillate

from side to side at an angle of approximately 90°.

■ To turn o the oscillation, pull the toggle switch A6 up. This will

turn o the oscillation.

Setting the vertical tilt angle of the motor unit

■ Before setting the vertical tilt angle of the motor unit A7, rst

turn o the fan. Set the desired angle of the motor unit A7 and

then you may start the fan again.

Note:

The motor unit A7 may only be tilted up and down in

alimited range. Do not set the tilt angle of the motor unit

A7 by force.

CLEANING AND MAINTENANCE

■ Before cleaning it, make sure that the appliance is turned o

and disconnected from the power socket.

■ Regularly remove dust from the appliance. For normal cleaning,

aclean, dry cloth is sucient. In the event that it is dirtier,

disassemble the appliance and wipe the individual parts

with awiping cloth slightly dampened in asolution of warm

water and neutral detergent. Then wipe everything so that it is

thoroughly dry. Make sure that no water enters the motor unit

A7 or into the control panel A8 while cleaning.

■ Prior to reassembly, make sure that all parts of the appliance

are dry.

■ Do not submerge the appliance or its power cord in water and

do not wash it under running water.

■ For cleaning do not use steel wool, cleaning products with an

abrasive eect, petrol and other solvents.

STORAGE

■ If you will not be using the fan for an extended period of time,

store it in aclean, dry place or disassemble it and put it back

into the box.

Sencor SFE 2311 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sencor SFE 2311

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info