Bedienungsanleitung Sencor SFE 4030 (Seite 6 von 8) (Englisch)

759909

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

EN-6

Desktop Fan

SFE 3020WH / SFE 4030WH

2014 06/2014

FAN ASSEMBLY

 Place the stand Aqa on an level, dry and stable surface. Place the holder A9 into the holes in the

stand Aqa and secure it in place with the supplied screws Aqs (total 3 pcs).

 Unscrew the nut A2 and A4 from the motor shaft A6. Seat the rear protective grill A5 on to

the motor shaft A6 in such a way that the fan carrying handle attached to the rear grill A5 points

upwards. Push the rear grill A5 towards the motor unit A7 ensuring the lugs on the front part of

the motor unit A7 pass through the holes in the central part of the rear grill A5. Use the nut A4

to secure the grill A5 to the motor unit A7.

 On to the motor shaft A6 place the fan blades A3 and push them fully in the direction of the

motor unit A7. The motor shaft A6 ends in the shape of a letter T. Make sure that the shaft A6

correctly ﬁ ts into the hole in the centre of the fan blades A3. Connect the fan blades A3 to the

shaft using the fastening nut A2.

 On the outer band of the protective grill A1 there are three fastening clamps, a hook and a screw

hole. Release the clamps and hold the grill A1 in such a way that the hook is located on the top

part of the grill A1. Place the front grill A1 against the back grill A5 in such a way that the outer

band of the grill A5 ﬁ ts into the hooks on the outer band of grill A1. Check that the outer bands

and the screw holes overlap. Fold down the clamps to fasten the outer bands together. For safety

reasons secure the outer band connection using the supplied screw and nut. If during the assembly

of the fan you proceeded according to the above instructions, the screw holes are located in the

bottom part of the outer band.

 The fan is now assembled and ready for use.

OPERATING THE FAN

 Connect the fan to a power socket.

1) Setting the speed and turning off the fan

Turn the dial Aq; to position 1 to set the fan to low speed. Turn the dial Aq; to position 2 or 3

to set the fan to medium or high speed. Turn the dial Aq; to position 0 to turn off the fan.

2) Activating and deactivating oscillation

If the fan is running, push switch A8 downwards to activate the oscillation of the motor unit A7.

The motor unit A7 will oscillate horizontally. To deactivate the oscillation pull switch A8 upwards.

3) Setting the vertical tilt of the motor unit

Before setting the vertical tilt of the motor unit A7, ﬁ rst turn off the fan by turning the dial Aq;

to position 0 (off). Set the desired vertical tilt angle of the motor unit A7 and then turn the fan on

again.

Note:

The motor unit A7 may only be tilted in a limited range. Do not use force to set the tilt angle

of the motor unit A7.

 If you will not be using the fan, turn it off according to the instructions contained in paragraph

"Setting the speed and turning off the fan" and disconnect it from the power socket.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sencor SFE 4030 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info