Bedienungsanleitung Sencor SFN 4040 (Seite 8 von 10) (Englisch)

759906

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

EN-8

Pedestal Fan

SFN 4040SL

2019 12/2019

DESCRIPTION OF THE APPLIANCE

A1 Protective grille (consists of two parts: front and rear)

A2 Fan blades with adiameter of 40 cm

A3 Motor unit

A4 Horizontal oscillation toggle switch

A5 Speed selector 0 - o, 1 - low speed, 2 - medium speed, 3 - high speed

A6 Screw for attaching the motor unit to the pole

A7 Fan head tilt angle adjustment screw

A8 Extensible pole

A9 Pole extension lock

A10 Base

Note:

The accessories include ascrew and anut for joining the protective grills.

BEFORE FIRST USE

■ Take the appliance and its accessories out of the packaging materials. Before disposing of the packaging materials,

make sure that no part of the appliance is missing.

ASSEMBLING AND DISASSEMBLING THE APPLIANCE

■ Before assembling or disassembling the appliance, make sure that it is turned o and disconnected from the

power socket.

■ Remove the nut from the underside of the extensible pole A8. Seat the extensible pole A8 on the base A10 so that

the opening of the extensible pole A8 is aligned with the hole in the base A10. Secure the extensible pole A8 in

place using the nut. Check that it is correctly tightened.

■ Remove the four screws A3 from the motor unit. Place the rear part of the protective grille A1 on to the motor unit

A3 so that the holes in the motor unit A3 are aligned with the holes in the protective grille A1. Secure the rear part

of the protective grille A1 using the screws.

■ Place the fan blades A2 on to the shaft of the motor unit A3 and rmly tighten the screws.

■ Now attach the front part of the protective grille A1 and fasten both parts together using the metal clamps and

asmall screw, which is apart of the grille assembly.

■ Place the motor unit A3 with the attached fan head on the extensible pole A8 and secure the fan head using the

screw A6.

■ Before putting the fan into operation, check that it is correctly assembled and that the protective grills are rmly

joined.

■ To disassemble, proceed in reverse sequence.

OPERATING THE APPLIANCE

Setting the speed and turning o the fan

■ Place the fan on an even, dry and smooth surface within reach of apower socket. Connect the power cord to

apower socket. To set the air ow speed, use the speed selector A5.

0 – turn o the fan;

1– set alow air ow speed;

2 – set amedium air ow speed;

3– set ahigh air ow speed.

■ When you have nished using the fan, always turn it o and disconnect it from the power socket.

Setting horizontal oscillation

■ The horizontal oscillation of the motor unit A3 can be set using the toggle switch A4. To start the horizontal

oscillation, push the toggle switch A4 down. The motor unit A3 will oscillate from side to side at an angle of

approximately 90°.

■ To turn o the oscillation, pull the toggle switch A4 up. This will turn o the oscillation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sencor SFN 4040 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info