08/2018
- 9 -
Copyright © 2018, F
Because hair grows in various directions, it is also necessary to move the hair clipper
in various directions (upwards, down
Repeat individual passes so that you cut also the hair that you did not cut in the
previous passes.
Ensure that the flat part of the comb attachment is in full contact with the scalp.
will ensure an even haircut result.
T
the hair towards the hair clipper
Trim beards b
from the bottom upwards
mind that the selected comb attachment must be in constant contact with the skin
in order to ensure an even cut. After r
unit A2 , do not forget to set the cutting height again.
Regularly clean away hair and whiskers from the cutting unit. In the event that
a
hair clipper and blow or tap the hair or whiskers out of it.
CLEANING AND MAINTENANCE
Regular cleaning of the hair clipper after every use will ensure its proper operation.
Before you start cleaning the hair clipper
socket.
Attention:
This hair clipper is not designed to be washed under awater tap. Do
not spray the hair clipper or its power adapter A8 with wa
other liquid or submerge it in water or any other liquid.
CLEANING THE CUTTING UNIT
Remove the comb attachment from the cutting unit A2 when it is ready
Use the cleaning brush B9 to remove all hair
unit A2 and all the remaining attachments B1 to B8 .
Remove the cutting unit A2 from the hair clipperE . Hold the hair clipper in
one hand so that your thumb is positioned on the underside of the cutting unit A2 .
Use the thumb of the other hand to push the cutting unit from the handle A6 until
the cutting unit A1 is fully released.
Attention:
The edge of the cutting blade A1 is sharp, pay increased
attention when handling it.
Use the brush B9 to remove all hair or whiskers frA2 and from
the inner area of the hair clipper underneath the cutting unit A2 .
After cleaning, reattach the cutting unit A2 to the handle of the hair clipper A6 , see
figure F . Slide the tab on the underside of the cutting unit A2 into the cut-out in
the handle of the hair clipper A6 and then push the cutting unit A2 against the hair
clipper until an audible click is heard.
CLEANING THE C
Comb attachments B1 to B8 can be washed under lukewarm running water
washing an attachment, carefully wipe it with asof
dry naturally.
The hair clipper handle A6 can be cleaned using aclean dr
it is very dirt lightly dampened cloth. Then thor
cleaned surface dr
TA8 , use aclean, dry cloth.
For cleaning, do not use brushes with har
abrasive effect, solvents, et
LUBRICA
TA1 , w
is regularly lubricated always after several sessions
If acomb attachment is mounted on the cutting unit A2 , remove it.
Apply 1 to 2 drops of oil B10 to the blade of the cutting unit A1 and evenly spread
the oil using acloth. Dr
using again.
Note:
After using up the supplied oil B10 you can use an oil that does not
contain acids, e.g
STORA
When you have finished using it, you ma
in the supplied case B11 . Keep the case with the hair clipper away from extreme
temperatures, direct sunlight and ex
dusty environment.
TECHNICAL SPECIFICA
Hair clipper
Built-in battery...............................................................................................
Output ............................................................................................................................................ 5
Dimensions (width × depth × height) .......................................................... 174 × 52 × 32 mm
Weight ............................................................................................................................................... 120g
Noise level ................................................................................................................................... 72 dB(A)
Pow
Rated voltage range .................................................................................................... 100−240 VAC
Rated frequency.......................................................................................................................50–60 H
Output ......................................................................................................................... 5
Length of the power cor
The declared noise emission level of the appliance is 72 dB(
Aof acoustic power with respect to aref
EXPLANA
Safety class for electrical shock protection:
IP20 – T way that it is not possible f
dangerous live parts of the appliance to come into contact with the human body and
at the same time the appliance is protected against the damaging effects of water that
could enter into the appliance.
Changes to text and technical parameters are reserved.
DISPOSAL OF USED BA
Prior to handing over the hair clipper at aspecialised collection facility, it is necessary
to ensure that the built-in battery is removed
authorised service centre. In the event that the product has been disassembled for the
purpose of ecological disposal then it must not be reassembled.
This symbol indicates that used batteries do not belong in ordinary
municipal waste. Hand over used batt
points for proper disposal. C
prevent negative impacts on the envir
Disposal in other countries outside the European Union.
This symbol is valid in the European Union. If you wish to dispose of
used batteries, request the necessary information about the correct
disposal method from the local authorities or from your vendor
INSTRUCTIONS AND INFORMA
DISPOSAL OF USED P
Dispose of used packaging material at asite designated f
DISPOSAL OF USED ELECTRICAL AND ELEC
EQUIPMENT
This symbol on products or original documents means that used
electric or electronic products must not be added to ordinary
municipal waste. F
these appliances to determined collection points. Alternatively
some European Union states or other European c
return your appliances to the local retailer when buying an equivalent
new appliance. Correct disposal of this product helps save valuable
natural resources and prev
environment and human health, which could result fr
waste disposal. Ask your local authorities or collection facility for more details
accordance with national regulations penalties ma
disposal of this type of waste.
For business entities in Eur
If you want to dispose of electric or electronic appliances, ask your retailer or supplier
for the necessary information.
Disposal in other countries outside the European Union.
This symbol is valid in the European Union. If you wish to dispose of this product,
request the necessary information about the correct disposal method from the local
council or from your retailer
This product meets all the basic requirements of EU directives rela
it.
