Bedienungsanleitung Sencor SSV 230 (Seite 6 von 7) (Englisch)

758414

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

06/2017

EN Electric Spiralizer

User'smanual

■ Prior to using this appliance, please read the user’smanual thoroughly,

even if you already have experience in using similar appliances. Only

use the appliance in the manner described in this user’smanual. Keep

this user’s manual in asafe place where it can be easily retrieved for

future use.

■ We recommend saving the original cardboard box, packaging

material, purchase receipt and responsibility statement of the vendor

or warranty card for at least the duration of the legal liability for

unsatisfactory performance or quality. In the event of transportation,

we recommend that you pack the appliance in the original box from

the manufacturer.

DESCRIPTION OF THE APPLIANCE

A1 Button for releasing the

extension of the inner part of

the pusher

A2 Inner part of the pusher

A3 Pusher outer case cover

A4 Pusher outer case

A5 Lid with feed tube

A6 Blade holder with aperipheral

cog wheel

A7 Blade for cutting spaghetti

strips measuring 3 × 3 mm

A8 Blade for cutting spirals,

cutting thickness 3 mm

A9 Insertion hole for the blade

holder

A10 Jug lid

A11 1.7-litre transparent jug

A12 Drive unit

A13 0/Iswitch (o/on)

A14 Anti-slip feet

BEFORE FIRST USE

1. Take the appliance and its accessories out of the packaging materials.

2. Thoroughly wash all parts that are intended to come into contact with

food using warm water and aneutral kitchen detergent. Then rinse

under clean water and allow them to dry naturally or dry them using a

wiping cloth. Do not submerge the drive unit A12 in water or rinse it

under running water.

Attention:

Be especially careful when cleaning the blades A7 and A8 to

avoid injury on the sharp edges.

ASSEMBLING AND DISASSEMBLING THE APPLIANCE

■ Before you start assembling or disassembling the appliance, check

that it is turned o and disconnected from the power socket.

■ Place the drive unit A12 on an even, dry and stable surface. Place

the jug A11 under the insertion hole A9 so that the handle points

outwards and so that it is properly seated in its place (see g. C1).

Otherwise, the appliance will not start when turned on. The lid A10

serves to cover the jug A11 when it is not located in the drive unit

A12, for short term food storage.

■ Insert the blade A7 or A8 from above into the holder A6 and push

down the blade edges to that the blade ts in along the entire

perimeter of the holder A6 (see g. B1).

Attention:

When inserting blade A7 or A8 into the holder A6 take care not

to injure yourself on its sharp edges.

■ Insert the assembled holder with the blade from above into the

insertion hole A9 ensuring that the peripheral cog wheel on the

holder A6 slides into the cog wheel that is apart of the drive unit A12

(see g. C2). On to the drive unit A12 place the lid with the feed tube

A5 so that the arrow symbol marked on the lid A5 is aligned with the

open padlock symbol marked on the drive unit A12 (see g. C3). Turn

the lid A5 clockwise all the way to secure it in position. The arrow

symbol marked on the lid A5 is now aligned with the closed padlock

symbol on the drive unit A12. Unless the lid A5 is properly attached,

the appliance will not start when turned on.

■ Into the outer case A4 insert the inner part of the pusher A2, and to

connect these two parts press the cover A3 towards the outer case

A4 while at the same time turning it anticlockwise all the way. Insert

the pusher assembled in this way into the feed tube A5 (see g. C4).

Button A1 serves to release the extension of the inner part of the

pusher A2. When button A1 is pushed, the inner part of the pusher

A2 will extend out upwards. This will release the remaining foodstus

from the bottom part of the pusher when the appliance is used. Lock

the extension in place by pushing the inner part of the pusher A2

down into the outer case A4 until it is secured in place by both latches

on the inner part of the pusher A2 in the cover A3.

■ Disassemble the appliance in the reverse sequence. To remove the

blade A7 or A8 from the holder A6, it is rst necessary to push down

the latches of the blade A7 or A8 from underneath (see g. B2). This

will release the blades and it is then possible to remove them.

OPERATING THE APPLIANCE

1. This appliance is suitable for processing harder types of fruits and

vegetables such as, for example, carrot, apple, celery, zucchini,

cabbage, beetroot, pumpkin, cucumber, potatoes, sweet potato, etc.

in the raw form. It is not particularly suitable for processing soft types

of fruits and vegetables.

2. Thoroughly wash all the fruit and vegetables. Certain types may need to

be cut up to pass through the hole of the feed tube A5. This means that

the diameter of the fruit or vegetable should not be greater than 75 mm

and the length should be no greater than 175 mm. Kernels and stones

also need to be removed from certain types of fruit and vegetables.

Attention:

Never attempt to use this appliance to process hard stones

contained in, for example, mangoes, etc.

3. Make sure that the appliance is properly assembled and located on

an even, dry and stable surface. Connect the power plug to apower

socket and set the switch A13 to position I(on).

4. Start gradually inserting the fruit or vegetables into the hole of the

feed tube A5 and push them through the feed tube A5 with the

properly assembled pusher. To release any remaining foodstus from

the bottom part of the pusher, use button A1 as described in chapter

Assembling and disassembling the appliance.

Attention:

Do not use ngers or other items to push food in.

The maximum continuous operating time is 1 minute. Before

turning it on again, allow the appliance to cool down for at least

5 minutes.

5. In the event that the jug A11 lls up during operation, turn o the

appliance, disconnect it from the power socket and make sure that the

rotating parts have stopped. Empty the jug A11 and put it back in its

place. Then you can use the appliance again.

6. When you have nished using it, set the switch A13 to position 0

(o), disconnect the appliance from the power socket and clean it out

according to the instructions contained in the chapter Cleaning and

maintenance.

QUICK GUIDE TO PROCESSING FRUIT AND VEGETABLES

Type of fruit or

vegetable

Type of blade Maximum

amount per

batch

Approximate

operating

time

Carrot A7 or A8 500 g 30 s

Potatoes A7 or A8 500 g 30 s

Cucumber A7 or A8 500 g 30 s

Cabbage A7 500 g 30 s

Zucchini A7 or A8 500 g 30 s

Sencor SSV 230 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sencor SSV 230

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info