- 10 - 05/2020
Copyright © 2020, F
USING THE SA
1. Make sure that the food processor is correctly assembled and that the speed
control knob A13 is set to the OFF position. Insert the power plug into a
socket.
2. Prepare asausage casing that you will stu with ground meat and allow it to soak
in lukewarm water for appro
the hopper B2 . T
end and slide the other end like asock on to the sausage stuer attachment B12 .
3. Use the speed control knob A13 to set the desired speed.
initially set the lowest speed and then increase it as requir
the sausage casing on the attachment B12 and use the other hand to push the
ground meat mixture with the pusher B1 through the feed tube B3 . If the sausage
casing sticks to the attachment B12 , it is necessary to moisten it with water again.
Attention:
Do not use fingers or other items to push the ground meat in.
Always use the pusher B1 designed for this purpose
4. TA13 to the OFF position.
5. Clean out the individual par
instructions in chapter Cleaning and maintenance.
ASSEMBLING AND DISASSEMBLING
A
1. Proceed in the same way as when assembling the meat grinder
dierence that instead of the grinding blade B6 and the gB8 , B9 or
B10, only parts B13 a B14 are used.
2. Place the moulder B13 on to the screw shaft B5 so that the notch in the grinding
chamber B4 ts into the groove in the moulder B13 . Place the kebab moulder
attachment B13 on to the conical attachment B14 and complete the entir
maker assembly by screwing the screw ring B7 on to the grinding chamber B4 .
Place the stainless steel hopper B2 on to the feed tube B3 .
3. Attach the attachment to the food processor in the same way as described in point
4 in chapter Assembling and disassembling the meat grinder
4. When disassembling, rst remove the hopper B2 . A1 and
remove the attachment by turning it clockwise. After r
put the cover A2 back in its place.
5. When disassembling the attachment into its individual parts, proceed in the
reverse sequence.
USING THE KEBAB MAKER A
1. Make sure that the food processor is correctly assembled and that the speed
control knob A13 is set to the OFF position. Insert the power plug into a
socket.
2. Place the prepared kebab meat mixture on to the hopper B2 . Use the speed c
knob A13 to set the desired speed.
and then increase it as required. Using the pusher B1 , push the mixture thr
the feed tube B3 .
pieces.
from ground meat and whole grain wheat
Attention:
Do not use fingers or other items to push the ground meat in.
Always use the pusher B1 designed for this purpose
3. TA13 to the OFF position.
4. Clean out the individual par
instructions in chapter Cleaning and maintenance.
ASSEMBLING AND DISASSEMBLING THE C
1. Proceed in the same way as when assembling the meat grinder
dierence that instead of the grinding blade B6 and the gB8 , B9 or
B10 only parts B11, B15 and B16 are used.
2. Place the separator B11 on to the screw shaft so that the notch in the g
chamber B4 ts into the groove in the separator B11 . Insert the cookie maker
holder B16 into the screw ring B7 . Screw the screw ring B7 clockwise on to the
grinding chamber B4 . Complete the assembly by inserting the cookie maker B15
into the holder B16 and attaching the hopper B2 to the feed tube B3 .
3. Attach the attachment to the food processor in the same way as described in point
4 in chapter Assembling and disassembling the meat grinder
4. When disassembling, rst remove the hopper B2 . A1 and
remove the attachment by turning it clockwise. After r
put the cover A2 back in its place.
5. When disassembling the attachment into its individual parts, proceed in the
reverse sequence.
USING THE C
1. Place the prepared dough on to the hopper B2 . Slide the cookie maker B15 to the
left or right to set the desired cookie shape.
2. Insert the power plug into apower socket. Set the required speed using the speed
control knob A13 . When starting it for the rst time, w
speed 3 and then increase or decrease it as required
3. Use the pusher B1 to push the dough through the feed tube B3 . The food
pr
cookie maker B15 . W
the pushed out dough. T
Attention:
Do not use fingers or other items to push the dough in. Always
use the pusher B1 .
4. When you have nished using the food processor
control knob A13 to the OFF position.
5. Clean out the attachment af
Cleaning and maintenance.
BLENDING
ASSEMBLING AND DISASSEMBLING THE BLENDER
1. On to the blending jar C4 , place the outer lid C2 so that its edges copy the neck of
the jar
lid C2 , place the inner cap C1 and push it down all the way
2. Make sure that the food processor is turned o and disconnected from the power
socket. TA8 must be tilted down in the horizontal position
and the whisk, beater or kneading attachments must be removed. Release and
remove the top attachment hub cA7 . Place the assembled blending jar on to
the top hub and pulling it gently turn it in the direction of the symbol all the way.
The safety mechanism will prevent the blender from starting unless it is correctly
secured to the multi-function head A8 .
3. T
4. Prior to starting the appliance, check that the blade assembly C6 is correctly seated
in the cu C5 . Properly tighten the cu C5 on to the mixing conC4 .
USING THE BLENDER
1. The blender is intended for preparing meals and drinks such as milkshakes, creamy
soups, sauces, spreads
vegetables, preparing potato pur
2. Assemble the blender according to the instructions in chapter Assembling and
disassembling the blender
up in advance) into the blending jar C4 .
Note:
The maximum capacity of the blending jar C4 is 1.5 litres. Never ll it past
the maximum mark. When processing hot liquids or liquids that expand in
volume during the blending process, it is rec
jar to no more than ⅔ of its maximum capacity.
3. Make sure that the food processor is correctly assembled and that the speed
control knob A13 is set to the OFF position. Connect the power cord to apower
socket. Set the required speed using the speed control knob A13 . W
to rst set aslower speed to allow the ingr
may be increased.
very quickly. A13 to the PULSE
position and hold it in this position for amoment. A
control knob A13 , it will automatically return to the OFF position.
Attention:
Hot liquids up to a temperature of 55 °C may be processed in
the blending jar
2 minutes. Do not leave the appliance in con
for longer than indicated above
30minutes.
4. While blending, you may add food or liquids to the blending jar C4 through the
hole in the lid C2 after removing the inner cap C1 . Never open the outer lid C2
during operation. When prC1 must remain
closed.
5. IC6 or the walls of the
blending jar C4 , turn the appliance o by turning the speed control knob A13
to the OFF position and disconnect it from the power socket. Make sure that
the blade assembly C6 has stopped rotating. Car
blending jar from the multi-function head A8 by turning it in the direction of the
symbol . TC6
and the inside of the blending jar C4 . Put the lid back on and reattach the blender
assembly to the multi-function head A8 . Plug the power cord into apower socket
and continue blending.
6. After you have nished using the appliance, set the speed contrA13 to the
OFF position and disconnect the power cord from the pow
the blade assembly C6 has stopped rotating and carefully take the blending jar
assembly o the multi-function head A8 . Put the cover A7 back in its place and use
asoft plastic spatula to remove food frC4 .
