759451

Sencor SVC 1038 Seite 5

5
Zoom out
Zoom in
Vorherige Seite
1/6
Nächste Seite
- 5 - 09/2020
Copyright © 2020, Fast ČR, a.s.
EN Bagless vacuum cleaner
User'smanual
DESCRIPTION OF THE VACUUM CLEANER
A1 Cord winding button
A2 On/Off button
A3 Suction power control knob
A4 PUSH button (serves to release the
dust container)
A5 Rubber coated wheels
A6 Dust container lid
A7 Dust container
A8 Hose connection hole
A9 Handle
A10 Sliding flap for air suction
A11 Telescopic tube
A12 Telescopic tube position lock
A13 Combination floor nozzle
A14 Flap position for vacuuming carpets
A15 Flap position for vacuuming hard
(smooth) floors
A16 Hose
A17 Accessory holder
A18 Stopper for the horizontal and
vertical parking position
A19 Clip
A20 Hose end
A21 Front travel wheel
A22 Vertical parking position
A23 Power cord
A24 Inflow filter
A25 Foam pre-filter
A26 Horizontal parking position
A27 Outflow filter
A28 Outflow filter protective grille
A29 Long flexible crevice nozzle
A30 Crevice nozzle
A31 Upholstery nozzle
A32 Brush attachment (easy to attach
to the upholstery nozzle for gentle
vacuuming of fine upholstered
surfaces)
A33 Hard floor nozzle
A34 Mini turbo brush
ASSEMBLY
Inserting the hose into the air suction hole on the vacuum cleaner.
■ Press both the clips on the end of the hose A20 and insert it into the air suction hole
A8 on the vacuum cleaner until you hear a"click". The hose A16 is now secured in
the correct position.
Attach the holder to the telescopic tube:
■ Make sure to place the holder with the hose on the wider part of the telescopic
tube A11.
Attach the floor nozzle to the telescopic tube:
■ Make sure that the floor nozzle A13 is attached to the narrower part of the
telescopic tube A11.
Adjust the length of the telescopic tube:
■ Adjust the length of the telescopic tube A11 as required – disengage and hold the
clip A19 on the tube in the direction shown by the arrow and adjust the length
of the tube A11 as required. Then release the clip A19 and slide out the tube A11
slightly forward until you hear a"click". The telescopic tube A11 is now securely
locked in position.
USING THE VACUUM CLEANER
Connecting the vacuum cleaner to the power grid
■ Wind out the required length of the power cord by pulling on the power plug. Insert
the power plug into apower socket.
Attention:
The yellow marking on the power cord warns you that the power
cord is close to its end. Do not pull the cord farther than the red
marking.
Adjusting the floor inlet nozzle according to the floor surface.
■ You may set the inlet nozzle according to the floor surface by adjusting the inlet flap:
- If you want to vacuum carpets, move the flap to retract the bristles.
- If you want to vacuum hard and smooth surfaces, move the flap to extend the
bristles.
Turning your vacuum cleaner on and off
■ To turn on the vacuum cleaner, press the On/Off button A2. To turn off the vacuum
cleaner, press the button A2 again.
Adjusting the suction power
■ Suction can be controlled using the control knob A3. Turning clockwise (towards
MAX) increases the power of the vacuum cleaner, turning anticlockwise (towards
MIN) reduces the power. In asmaller range, you may regulate suction power using
the mechanically sliding flap A10 on the hose handle.
TIPS
■ Use the maximum suction power when vacuuming carpets or floors with ahard
surface. Use the reduced strength when vacuuming upholstery, window curtains,
etc.
■ If the hose holder becomes blocked when vacuuming, disconnect it from the
telescopic tube and also disconnect the hose from the vacuum cleaner body.
Then place the holder inside the suction hole on the vacuum cleaner body and
vacuum the stuck dirt out.
Temporary interruption of the vacuuming process
■ If you wish to interrupt vacuuming for awhile, you can use the horizontal A26 or
vertical A22 parking position on the vacuum cleaner, into which you insert the
stopper A18 on the floor nozzle.
Attention:
Do not move the vacuum cleaner from place to place if the hose
is in the parked position! The stopper on the floor nozzle could
brake off.
Ending the vacuuming process
■ When you finish vacuuming, switch the vacuum cleaner off by pressing the On/Off
button A2 and then disconnect the power cord plug from the power socket.
■ To wind the power cord back into the vacuum cleaner, press and hold the winding
button A1 with one hand and guide the power cord with the other.
TIP:
■ If the winding process stops and part of the power cord is still outside, release the
winding button A1 and pull the cable out again by about 50 cm and then press
and hold the winding button A1 again and repeat the winding process.
USING THE ACCESSORIES
■ The combination floor nozzle A13 for hard floors ensures perfect and yet gentle
vacuuming of smooth hard surfaces thanks to the brush being from 100 % natural
bristles. It can be used to vacuum floors that are sensitive to scratching such as
wooden or floating floors, marble floors, tiles, linoleum, etc.
■ The long flexible crevice nozzle A29 serves to vacuum very hard-to-reach places
anywhere in your car.
■ The crevice nozzle A30 is suitable for vacuuming hard to reach places (e.g. window
frames, libraries, upholstery corners, joints, etc.).
■ The hard floor nozzle A33 ensures perfect and yet gentle vacuuming of smooth
hard surfaces thanks to the brush being from 100% natural bristles. It can be used
to vacuum floors that are sensitive to scratching such as wooden or floating floors,
marble floors, tiles, linoleum, etc.
■ The mini turbo brush A34 is the ideal helper for removing animal fur, hair, etc.,
while at the same time being suitable for vacuuming hard-to-reach places. Its use
is not limited to the home, and can be used for vacuuming the car. It quickly and
effectively removes hair, animal fur and other materials from car seats, upholstery,
pillows and other textile surfaces.
TIP:
■ If during vacuuming you use an accessory very often, you may attach it to the
special holder on the telescopic tube.
CLEANING AND MAINTENANCE
Attention:
Before cleaning, disconnect this appliance from the power source.
Emptying the dust container
■ Empty the dust container A7 as soon as it fills up to the MAX mark; otherwise the
air flow and the suction power will be reduced. Nevertheless, it is recommended to
always empty out the dust container when you have finished vacuuming.
1. Take out the hose A16.
2. Press the PUSH A4 button and pull out the dust container A7 upwards.
3. Remove the lid of the container A6 and take out the dust filter. Tip the dust out of it
and rinse it out under lukewarm running water if necessary.
4. Take the dust container A7 above awaste bin and turn it upside down to shake the
dirt and dust out of it. If it is heavily soiled you may wash the entire container under
running lukewarm water. It is, however, necessary to first remove the inflow filter
A24 and its foam pre-filter A25 before doing this!
5. Insert the dust filter into the dust container A7 and put on the lid A6.
6. Insert the container A7 into the vacuum cleaner.
Attention:
Make sure that all parts are completely dry before reinserting
the dust container A7 and the dust filter back into the vacuum
cleaner.
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sencor SVC 1038 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info