- 5 - 07/2020
Copyright © 2020, F
EN V
User'smanual
A1 Cord winding button
A2 Full dust bag indicator
A3 Vacuum hose connection hole
A4 Clip for locking and releasing the
lid
A5 Button for opening the accessory
compartment
A6 Buttons +/- serve to control the
power of the motor
A7 ST
A8 Rubber-coated wheel
A9 Handle
A10 Sliding ap for air suction
A11 T
A12 Clip for the telescopic tube
A13 Floor nozzle
A14 Flap position for vacuuming
carpets
A15 Flap position for vacuuming hard
(smooth) oors
A16 Hose
A17 Accessory holder (depending on
the model)
A18 Stopper for the horizontal and
vertical parking position
A19 Clip
A20 Hose end
A21 Horizontal parking position
A22 Power cord
A23 Carry handle
A24 Front trav
mechanism
A25 Vertical parking position
A26
T
in hard to reach places (e.g
corners, book shelves, areas between
mattresses, upholstery, et
A27 Upholstery nozzle with an
additional brush
A28 Hard oor nozzle
A29 Mini turbo brush
A30 Long exible crevice nozzle
A31 Dust bag collar
A32 Dust bag
A33 Dust bag holder
A34 Inow micro-lter
A35 Grill of the inow micro-lter
A36 Outow micro-lter
A37 Outow HEP
A48 Grill of the outow micro-lter
and HEP
ASSEMBL
Inserting the hose into the air suction hole on the vacuum cleaner:
Press both the safety buttons on the end of the hose A20 end and insert the hose end
A20 into the air suction opening A3 on the vacuum cleaner until you hear a
hose A16 is now secured in the correct position.
Attach the holder to the telescopic tube:
Make sure to place the holder with the hose on the wider part of the telescopic tube A11 .
Attach the oor nozzle to the telesc
Make sure the oor nozzle A13 is attached the narrower part of the telescopic tube A11 .
Adjust the length of the telescopic tube:
Adjust the length of the telescopic tube A11 as required – disengage and hold the clip
A12 on the tube A11 in the direction shown by the arrow and adjust the length of the
tube A11 as required. A12 and slide out the tube A11 slightly
forward until you hear aA11 is now securely xed in position.
USING THE V
Connecting your vacuum cleaner to the pow
Wind out the required length of the powA22 by pulling on the power plug. Insert
the power plug into apower socket
Caution:
Y
is close to its end. Do not pull the cord further than the red
marking.
Adjusting the oor inlet nozzle accor
YA13 according to the oor surface by adjusting the inlet ap:
• If you want to vacuum carpets, close the bristles of the inlet inside the inlet nozzle
by turning the ap accordingly
• If you want to vacuum hard and smooth surfaces, extend the bristles out of the
nozzle, by turning the ap accordingly
T
TA7 . T
vacuum cleanerA7 again.
Adjusting the suction power
Suction can be controlled using buttons +/- A6 .
increased using the + button, decreased using the - button. In a
regulate suction power using the mechanically sliding ap A10 on the hose handle A9 .
Tips
• Use the maximum suction strength when vacuuming carpets
or oors with a hard surface. Use the reduced strength when
vacuuming upholstery, window curtains, etc.
• A9 becomes blocked when vacuuming,
disconnect it from the telescopic tube A11 and also disconnect
the hose A16 from the vacuum cleaner body
holder inside the suction hole on the vacuum cleaner body and
vacuum out the stuck dirt.
T
If you wish to interrupt vacuuming for aA21
A25 parking position on the vacuum cleaner, into which yA18
on the oor nozzle A13 .
Attention:
Do not move the vacuum cleaner from place to plac
A16 is in the parked position! The stA18 on the oor
nozzle A13 could brake o
Ending the vacuuming process
When you nish vacuuming, swi
button A7 and then disconnect the power cord plug from the socket.
TA22 back into the v
button A1 with one hand and guide the power cord A22 with the other
Tip:
If the winding process stops and part of the power cord A22 is still outside,
release the winding button A1 and pull the cable out again by about
50 A1 again and repeat
the winding process.
Carrying the vacuum cleaner
It is possible to hold and carry the vacuum by the handle A23 .
USING THE ACCESSORIES
The hard oor nozzle A28 ensures perfect and yet gentle vacuuming of smooth hard
surfaces thanks to the brush being from 100% natural bristles. It can be used to vacuum
oors that are sensitive to scratching such as w
tiles, linoleum, etc.
The mini turbo brush A29 is the ideal helper for removing animal fur
at the same time being suitable for vacuuming hard-to-reach places. Its use is not
limited to the home, and can be used for vacuuming the car
removes hair
other textile surfaces.
The long exible crevice nozzle A30 serves to vacuum very hard-to-reach places
anywhere in your car
CLEANING AND MAINTENANCE
Caution:
Before cleaning, disconnect this appliance from the po
source.
Changing the dust bag
When the full dust bag indicator A2 lights up, it is necA32 .
If you do not remove the dust bag A32 , the suction power will be reduc
1) A4 while pulling it upwards
at the same time.
2) A31 of the dust bag in the direction of the arrow, remov
from the plastic holder A33 and insert anew bag.
3)
Replacing and cleaning the inow micro-lter and outow HEP
1) A4 while pulling it upwards
at the same time.
2) A31 of the dust bag in the direction of the arrow, remov
from the plastic holder A33 to make room for the r
3)
Pull the inow micro-lter grill A35 towarA34 .
4)
tilt out the rear grill A38 of the outow micro-lter and HEPA38
aside and take out both lters.
5) A34 , A36 slightly soiled, it is possible to wash them under
running lukewarm waterA37 is slightly soiled, it is possible to
quickly wash it under aweak current of running lukewarm water
dust and dirt found on its surface. In the event of heavy soiling, replace the lters
with new ones.
6) A34 , A36 to dry naturally. Do not dry them over heaters or using
hair dryers. Then put the inoA34 , outow HEPA37 , micro-lter
A36 and the grills back in their place.
7) A32 .
8)
