Bedienungsanleitung Sentry EF3428E - Executive Fire-Safe (Seite 4 von 12) (Englisch, Französisch, Spanisch)

651323

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

3-Number Combination Lock

and Dual Combination Key Lock

NOTE: See the sticker on the back cover of

this manual for your combination.

IMPORTANT: The lock on this safe is

in the open position. DO NOT operate

the combination until ﬁrst reading and

understanding the following instructions.

Test ﬁrst

WITH DOOR OPEN!

Test your combination several times

with the door open.

To unlock and open

Before dialing your combination, simply insert the

key (if equipped) in the lock and turn clockwise.

1. Start the dial at ZERO.

2. Turn the dial to the left. Make sure ZERO

passes the pointer at least THREE times. Then

stop at the first number of your combination.

3. Turn the dial to the right. Stop the

SECOND time you reach the second number of

your combination.

4. Turn the dial to the left. Stop the FIRST

time the pointer reaches the third number of your

combination.

To Close and Lock

With the door closed, turn the handle

counterclockwise to secure the locking bolts, then

spin the combination dial to the left at least four

times to scramble the combination.

Standard Electronic Lock and

Dual Electronic Key Lock

To activate lock:

Four alkaline AA batteries, Voltage: 6Vdc, (not

included) are required to activate the keypad.

NOTE: Non-alkaline and rechargeable

batteries ARE NOT RECOMMENDED.

To install batteries:

1. Using two

hands, hold the

keypad, thumbs

down, on its

left and right

sides. Push up

the keypad with

your thumbs,

and disconnect it

from the safe by

pulling it towards

you. (Fig. A)

2. Let the

disengaged

keypad hang by

its wires. This will expose the battery holder.

(Fig. B)

3. Install four alkaline AA batteries as illustrated on

the back of the battery holder.

4. Reconnect the keypad by inserting the keypad’s

four posts into the matching holes.

5. Push down to snap into place.

Test ﬁrst

WITH DOOR OPEN!

(See back cover of this manual for your

factory code.)

Test your factory code several times with the door

open.

NOTE: Only a light touch is needed. A green

PROCEED light and a single beep indicate

that the keypad “felt” your touch. The

lock allows 5 seconds for each key press.

If you pause longer, an error signal will

occur (blinking red light and three beeps),

indicating you should start over.

For safes with dual combination key lock insert key

and turn clockwise.

1. Press the 5-digit factory code. The green light

will come on.

2. Turn the handle clockwise and open the door.

Access codes

There are three possible ways to unlock and

access the safe—by entering its preset Factory

Code, your own User Code or a User PIN (Personal

Identiﬁcation Number).

You can always open the safe by entering the

5-digit Factory Code. This code cannot be deleted.

But if you prefer to use your own code, you can

program the safe to open to the 5-digit User Code

of your choice. If you wish to give someone else

temporary access to the safe, you can program a

User PIN that can later be erased.

Programming a user code

There are two ways to program a user code.

A 1. Press the Program key. (Prog.)

2. Enter the Factory Code. The green LED remains

ON while you enter the 5-digit user code of your

choice. After 5 digits are entered the green LED

turns OFF.

(To enter a new User Code, repeat these steps.)

B 1. Press the red button on inside of door (hinge

side). The lock will “beep” and the green LED will

come on.

2. Enter a 5-digit user code.

(To enter a new User Code, repeat these steps.)

Keep your new user code secure

For your records, please copy it here:

_____ _____ _____ _____ _____

Programming a user PIN

1. Press the Program key.

2. Press it a second time.

3. Enter your 5-digit User Code. The green LED

remains ON.

4. Enter the 5-digit User PIN of your choice (any

combination except 00000.) After 5 digits are

entered, the green LED turns OFF.

(To enter a new User PIN, repeat these steps. To

erase the User PIN, press Program twice, enter your

User Code and then enter 00000.)

Key override

If your electronic lock fails or you do not have any

codes available, you may use a key override to

access this unit.

1. Using two hands, hold the keypad, thumbs

down, on its left and right sides. Push up the

keypad with your thumbs, disconnect and remove

the battery holder.

2. Insert the skeleton key into the key hole inside

the opening for the battery.

3. Turn the key to the right.

4. Open the door.

Lock instructions

Gaining Entry into Safes with Combination Locks

Gaining Entry into Safes with Electronic Locks

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sentry EF3428E - Executive Fire-Safe Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info