Bedienungsanleitung Shada 1000451 (Seite 3 von 10) (Deutsch, Englisch, Holländisch, Französisch)

663263

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

MV#: 20160920 08:45

Art. Nr.:1000451

• Do not use near infants/cribs and keep away from children.

Safety First!

CAUTION! - Use of controls or adjustments or performance of procedures other than those

speciﬁed herein may result in hazardous radiation exposure.

Avoid direct viewing of Class 2 laser energy. For reference the FLPPS requirements for demons-

tration laser products like laser pointers are limited to Class 2 levels of laser energy. This

product uses diractive optics to scatter the beam energy. This scattering eect causes

the energy concentration to drop below the exposure limits for momentary or accidental

viewing at a relatively short distance from the laser aperture. As similar with all bright

light sources, when you operate this device in unsupervised general public areas, it is

recommended that up-close access to The Outdoor Laser be restricted or prevented.

This laser display device incorporates a Class 2 laser system which, by itself, may be hazardous.

However, this laser display device incorporates a protective housing and diractive ho-

lographic optics in the machine’s design such that there is no exposure or human access

to the laser radiation during operation or maintenance above the Class 2 limits. Each

individual laser beams’s power is less than 1mW, which is about an average laser pointer.

UNDER NO CIRCUMSTANCE shall attempts be made to open the protective housing or operate

the device if the aperture windows are damaged. All service to this laser display device

requiring the protective housing to be opened and/or removed shall be performed by a

Outdoor Laser service personnel or their authorized agents. No user-serviceable parts -

opening The Outdoor Laser protective housing voids the warranty.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

cummunications

Probleml solving

Problem possible cause Solution

No light coming

from unit

• Remote control not working or

timer is on

• Electrical connection Outlet not

working

• Not within operating temperature

range.

• Unplug the light and plug back in (The Outdoor Laser will reset to default and should turn ON when plugged in).

• Check entire length of electrical cord for breaks in the wire and connections on both the projector and transformer.

• Check to make sure there is power to the electrical outlet supplying 230VAC at 50Hz. Use included transformer only.

• Operate unit within -25° C to 33°C. If below -25° C, leave unit on for at least 30 minutes until it warms up.

Dim or ﬂickering

light

• Not within operating temperature

range

• Unit is connected to a dimmer

• Improper power

• Debris on aperture glass

• Operate unit within - 25° C to 33° C. If below -25° C, leave unit on for at least

• 30 minutes until it warms up to operating temperature.

• Do not use with a dimmer.

• Check to make sure there is power to the electrical outlet supplying 230V at 50Hz. Use included transformer only.

• Clear aperture glass of any debris

One color appears

dimmer than the

other (if more

than one color)

•

The green light is much brighter

than the red

•

Some surfaces may absorb

certains colors or light causing it to

appear dim or non-existent

•

The human eye is most sensitive to green light and less sensitive to other colors. This is normal.

•

Position the projector to another surface for better eect. Brighter colored surfaces work best. Objects such as green

foliage may absorb red light.

Remote not wor-

king or operating

erratically

•

Remote batteries exhausted or

positioned improperly

•

Remote out of range or communi-

cation interference

•

Remote is not paired with

projector

•

Check LED indicator on the remote by pressing any button. If the LED is not working, then replace the batteries with a

fresh 23A cell aligning the “+” side of the battery with the “+” side of the remote control.

•

Extend the antenna on the remote for maximum range or move closer to the projector. Please note that overhead power

lines, microwaves, wireless routers, cordless phones and other devices may impact the communication between the

remote and The Outdoor Laser

•

projector.

•

Unplug desired Outdoor Laser to unpair and follow pairing procedures under „

Remote control Pairing

„ on the left page

WEEE NL: 3505

WEEE DE: 37281017

WEEE AT: 40133

Imported by

Kanaal Noord 350

NL-7323 AM Apeldoorn

www.shada.nl

LED’s

light

BRAND

SHADA

Shada 1000451 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info