Bedienungsanleitung Shark V1510 (Seite 6 von 6) (Englisch, Französisch, Spanisch)

668672

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

OPERATING INSTRUCTIONS

3. To use the flexible hose with

the dusting brush, hold the

hose in one hand and with the

other, pull out the dusting brush

and turn clockwise to lock in

place. (fig. 4)

Warning: Always unplug from

electrical outlet before opening the dust

cup (container).

Note: HEPA dust cup filter must be

used when operating the hand vacuum.

Using The Unit As A Hand

Vacuum

1. Insert the dusting brush/hose

connector into the brush chamber

exhaust port. Lock the flexible hose in

place by clipping the hose into the

hose holder. (fig. 1)

Cleaning With the Hose

CAUTION: The Hand Vacuum is

a very powerful unit. Make sure

that you hold it firmly, otherwise it

can slip out of your hand and

cause injury.

To use the hand vacuum with only the

hose and the dusting brush or crevice

tool:

1. Rotate the brush cover by pushing on

the brush cover release button until it

clicks in place. (fig. 2)

2. Remove the flexible hose from the

brush chamber exhaust port and take

the hose out from the hose holder.

(fig. 3)

Fig. 1

Fig. 2

Fig. 3

Fig. 4

3. To use the flexible hose with

the crevice tool, make sure that

the brush is in the storage

position and insert the crevice

tool into the opening of the

hose. (fig. 5)

Fig. 5

OPERATING INSTRUCTIONS

Cleaning & Changing the

HEPA Dust Cup Filter

Warning: Always unplug the unit from

electrical outlet before opening the Dust

Cup (container).

Important: Do NOT use the HEPA filter

cartridge without the debris screen in

place.

Warning: After each Use - Always

remove the Filter Debris Screen from the

HEPA Dust Cup Filter, then vigorously

“TapClean” HEPA Filter until no more

dust can be removed.

2. To open the Dust Cup (container),

push button and remove the Dust

Cup (container ). (Fig. 7)

Dust cup release button

Fig.7

3. Rotate the lower dust cup clockwise

to separate it from the filter chamber.

Empty and clean the dust cup. (fig. 8)

IMPORTANT

, Please Note : The

“TapClean” HEPA Dust Cup Filter &

Debris Screen will stop most of the tiniest

dust particles and airborne allergens from

re-entering the air you breathe. In fact it

stops 99.97% of all particles as small as

0.3 microns - many times smaller than a

human hair!!! Because of this incredible

filtration performance, the HEPA Dust Cup

Filter will quickly accumulate, inside the

white filter folds, many fine dust particles

that are difficult to see but which will

eventually block or reduce your suction

power - if not cleaned properly. Clean the

HEPA Filter and Debris Screen after each

use as described in this section.

Fig.8

Filter

Chamber

Dust

Cup

4. Remove the HEPA Filter from the filter

chamber. (fig. 9)

5. Separate the debris screen from the

HEPA filter cartridge by grasping the

debris screen with one hand and the

filter frame with the other and pull

apart. (fig. 10)

Fig. 9

Filter

Chamber

HEPA

Filter

Debris

Screen

Fig. 10

1. To remove the dust cup (container),

hold the unit in the upright position

to prevent the dust from falling out

of the dust cup. (Fig. 6)

Fig. 6

HEPA

Filter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Shark V1510 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Shark V1510

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info