Bedienungsanleitung Sherwood PM-9901 (Seite 7 von 9) (Englisch)

572498

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

CHANGING THE SPEED

O P E R A T I O N STYLUS REPLACEMENT

1. Push the power button to turn on the power, the

speed indicator and the strobe-illuminator will light up.

2. Place a record on the slip mat, when playing a

45rpm record with a large center hole, place the

45-rpm adaptor on the center spindle.

3. Set the speed to match the record.

4. Remove the stylus protector, release the arm clamp.

5. Set the cueing lever to the up position.

6. Press the Start/Stop button, the turntable platter

will start to rotate.

7. Move the tonearm over the desired groove.

8. Set the cueing lever to the down position, the

tonearm will descend slowly onto the record and

play begins.

9. When play is finished, raise the cueing lever, move

the tonearm to the arm rest, secure the tonearm

with the arm clamp.

10. Press the Start/Stop button to stop the platter

rotating, push the power button to turn off the power.

Suspend play

Set the cueing lever to "UP"position during play, the

stylus tip of the cartridge will be lifted from the record.

Target light

This unit is provided with a target light for illumi- nating

the stylus tip during play.

Push the target light button, the target light will be

raised into position for illuminating the stylus tip.

When not in use, keep the target light lowered

through depression.

As long as the pitch control (13) is in center click

position,the turntable is operated witch quartz- controlled

rated speed.The green LED (12) will then be lit.

The speed can be increased or decreased by 10% via

the pitch control (13). The red LED (12) will then be lit. If

the change of speed does not correspond to the pitch

control change, it is possible to correct this with the trim

control (15).

An incorrect adjustment done on purpose can also be

used to have the turntable rotate extremely slow or fast.

The strobe dots (4) at the edge of the turntable issued

for speed monitoring.

The life expectancy of the stylus tip is 500 hours. For

the sake of maximum sound quality reproduction, we

recommend replacement within the minimum time limit.

1. The stylus tip is replaced by grasping the stylus

holder and pulling it away from the body of the

cartridge.

2. The new stylus tip s then inserted by pushing it into

the receptacle.

CARTRIDGE REPLACEMENT

Remove the headshell from thd tonearm, and the

screws that hold the cartridge. Pull out the four lead

wires from the cartridge itself. To protect the lead

wires at this point, remove the terminal pins with

pliers or the tip of the screwdriver.

The terminals on the accessory headshell are aligned

according to the arrangement below. Check the

location and polarity of each of the cartridge’s

terminal pins and then connect the lead wires, taking

care not to get the polarities mixed up.

Red : Right channel

White : Left channel

Green : Right channel ground

Blue : Left channel ground

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sherwood PM-9901 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info