Bedienungsanleitung Siemens AL140 Duo (Seite 9 von 12) (Englisch)

63603

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

L1a / GBR / A31008-M2001-L101-1-7619 / AL140_AL145_Kombi_GBR.fm / 13.08.2007

Base station power consumption

General specifications

Care

Wipe the base station, charging cradle and hand-

set with a damp cloth (do not use solvent) or an

antistatic cloth.

Never use a dry cloth. This can cause static.

Contact with liquid

If the handset has come into contact with liquid:

1. Switch off the handset and remove the bat-

tery pack immediately.

2. Allow the liquid to drain from the handset.

3. Pat all parts dry, then place the handset with

the battery compartment open and the keypad

facing down in a dry, warm place for at least

hours (not in a microwave, oven etc.).

4. Do not switch on the handset again until it is

completely dry.

When it has fully dried out, you will normally be

able to use it again.

Questions and answers

If you have any questions about using your phone,

visit us at

www.siemens.com/gigasetcustomer-

care at any time. The table below contains a list of

common problems and possible solutions.

AL140 AL145

In standby mode

– Handset in charging cradle

– Handset out of charging cradle

approx.

1.0 W

approx.

0.8 W

approx.

1.2 W

approx.

1.0 W

During a call approx.

1.0

approx.

1.2 W

DECT standard is supported

GAP standard is supported

Range up to 300 m outdoors

up to 50 m indoors

Base station power supply 230 V ~/50 Hz

Environmental conditions

operation

+5° C to +45 °C;

20% to 75% humidity

Problem Cause Solution

Nothing

appears in

the

display.

The handset is not

turned on.

Battery pack is

flat.

Press the end call key

a for approx. 5 sec-

onds or place the

handset in the base

station.

Charge/replace the

battery pack

(page 3).

No reaction

to key press.

The keypad lock is

activated.

Press the hash key

for approx. 2 sec-

onds (page 1).

No wireless

connection to

the base sta

tion, Base

flashes in

the

display.

The handset is

outside the range

of the base sta

tion.

The handset is not

registered.

The base station is

not turned on.

Cords not routed

correctly.

Move the handset

closer to the base

station.

(page 3).

Check the power con-

nector at the base sta-

tion (page 2).

Check cord routing

(page 2).

You cannot

hear a ringer/

dialling tone

from the fixed

network.

The phone cord

supplied has not

been used or has

been replaced by

a new cord with

the wrong jack

connections.

Please always use the

phone cord supplied

or ensure that the jack

connections are cor

rect when purchasing

from a retailer

(

page 2).

Error tone

sounds after

system PIN

prompt.

PIN forgotten.

You have entered

the wrong system

PIN.

Reset the system PIN

to the default 0000.

To do this, unplug the

mains unit from the

mains socket

£Press and hold the

paging key

£Plug the mains

adapter in again

£Hold the paging

key down for at least

another 2 seconds

and then release.

The

reset procedure is

now carried out.

The

handsets are de-

registered. The calls

list is cleared.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens AL140 Duo Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens AL140 Duo

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info