Bedienungsanleitung Siemens AS150 (Seite 4 von 11) (Englisch)

61045

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Gigaset AS150 / English / A31008-M1811-R601-3-TN19 / Wytana.fm / 05.05.2008

Setting up the telephone for use

Step 1: Connecting the base

Connect the phone jack with the phone cord 1

and the mains units (230 V) with the power cord

2 as shown. Place the cords in the cord recesses.

The two cords must be plugged in at all times.

◆ Only use the supplied mains unit (see the bot-

tom of the base) and the supplied phone cord.

◆ If you ever purchase another phone cord from a

store, ensure that the phone conductors are cor-

rectly connected: 3-4 connection of the telephone

conductors/EURO CTR37.

Step 2: Setting up the handset

Fitting the battery pack

◆ To open the battery compartment, push the

tongue on the battery cover inwards (see pic-

ture on left) and lift off the cover.

◆ Fit the left side of the battery pack under the

clips then press down on the right side so that

the pack snaps home.

◆ Plug the jack firmly into the socket (see picture

on right).

◆ To close the battery compartment, position the

cover and press until it snaps home.

Step 3: Registering the handset to the

base and charging the battery pack

Place your handset in the base with the display

facing forwards. The handset will now register

automatically to the base. For procedure see

page 4.

Charging the battery pack

To charge the battery pack, leave the handset in

the base for approx. ten hours. The battery pack is

now fully charged. The charge status of the battery

pack is correctly displayed only after uninterrupted

charging/discharging. You should not therefore

interrupt the charging process.

Charging is electronically controlled to prevent

overcharging. The battery pack heats up during

charging; this is normal and not dangerous. After

a time the charge capacity of the pack will

decrease for technical reasons.

You must set the date and time to ensure that the

times of calls are logged correctly (page 9). Your

telephone is now ready to use.

If you have any queries about the use of your tele-

phone, please read the tips under "Questions and

answers" (page 7) or contact our service (Cus-

tomer Care, page 8).

Activating/deactivating the handset

Press the 'end call' key a and hold.

If you place a deactivated handset in the base sta-

tion or charger, it will automatically activate.

◆ Place the battery leads in the cable

guides so that the battery cover cannot

catch on the leads and damage them

when it is closed.

◆ Only insert the recommended re-

chargeable battery pack, i.e. never use a

normal battery pack as this could damage

your health and cause injury.

◆ Never use non-Siemens battery charg-

ers as this could damage the battery pack.

◆ Only place the handset in the base/

charging cradle that is intended for it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens AS150 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens AS150

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info