Bedienungsanleitung Siemens EH611TA16E (Seite 5 von 20) (Englisch)

530782

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Important notes

Safety in use is only guaranteed if the technical installation of

the hob has been carried out correctly and in accordance with

the installation instructions. The installation technician shall be

liable for any damage caused as a result of incorrect

installation.

Only an authorised technician is able to connect the appliance.

The guidelines set out by the local electricity provider must be

observed.

This is a class I appliance and should only be used with an

earthed connection.

Using this appliance without an earth connection or after it has

been incorrectly installed may, under very rare circumstances,

cause serious harm.

The manufacturer accepts no responsibility for any malfunction

or damage caused by incorrect electrical installation.

If the appliance is not fitted with an accessible plug, means for

disconnecting it must be incorporated in the fixed installation, in

accordance with the installation regulations.

The inlet hose must be positioned so that it does not touch any

of the hot parts of the hob or oven.

Any change to the appliance's interior, including changing the

power cable, must be performed by the Technical Assistance

Service.

Induction hobs may only be installed over drawers, ovens with

the same brand of forced-air ventilation, or dishwashers of the

same brand. Refrigerators, unventilated ovens, and washing

machines may not be installed beneath the hob.

Assembly over drawer (figure 2a)

If the hob is installed above a drawer, metal objects stored

inside could become very hot due to the air recirculating from

the hob ventilation system. If this occurs, an intermediate

support is recommended.

A wooden panel can be used as an intermediate support

(figure 3), or you may order a suitable accessory from our

Technical Assistance Service.

The reference code for this accessory is 686002.

The worktop where the hob is installed should be at least

20 mm thick.

The distance between the top of the working surface and the

top of the drawer must be 65 mm.

Assembly over oven (figure 2b)

The working surface upon which the hob is installed must be at

least:

■ 20 mm thick if installed over a compact oven.

■ 30 mm thick if installed over a full-size oven.

If the hob is installed over a compact oven, there must be

60 mm distance between the top of the oven and the top of the

working surface.

Assembly over dishwasher (figure 2c)

If the hob is installed over a dishwasher, an intermediate

accessory must be installed. The accessory may be ordered

from our Technical Assistance Service.

The reference code for this accessory is 686002.

The working surface upon which the hob is installed must be a

minimum of 20 mm and a maximum of 40 mm thick.

The space between the top of the working surface and the top

of the dishwasher must be:

■ 60 mm if installed over a compact dishwasher.

■ 65 mm if installed over a full-size dishwasher.

Installing and connecting the hob - Figure 1/2/

3/4/5

Voltage, see specifications plate.

Connect using the connection drawing only.

Connection drawing - Figure 5

1. Brown

2. Blue

3. Yellow and green

Changing the connection current 13 / 16 / 20

Amps - Figure 6

Before using the hob for the first time, it must be tested for the

correct current.

Follow the steps below to change the current of the hob:

1. Turn on the hob with the main switch. Do not place any pans

on the hotplates

2. Within the following 60 seconds, adjust all hotplates to the

desired power level according to the required connection

current (see table).

3. Turn off all the hotplates in sequence, starting from the lower

right and continuing counter-clockwise.

4. The selected connection current is indicated in the display of

the right-hand lateral hotplates.

5. Turn off the hob with the main switch.

The selected connection current will have been properly saved.

Removing the hob

Disconnect the appliance from the mains.

Remove the hob by pushing it from below.

Power level Connection current in amperes

‚

20 A

16 A

„

13 A

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens EH611TA16E Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens EH611TA16E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info