641302
12
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
en Trouble shooting
12
3Trouble shooting
Trouble shooting
Sometimes certain faults detected can be easily
resolved. Before calling the Technical Assistance
Service, bear in mind the following advice:
Fault Possible cause Solution
The general electrical system
is malfunctioning.
Defective fuse. Check the fuse in the main fuse box and change it if it is
damaged.
The automatic safety switch or circuit breaker has
tripped.
Check the main control panel to see if the automatic safety
switch or circuit breaker has tripped.
The automatic switching on
function does not work.
There may be food or cleaning products stuck between
the ignition sparkers and the burners.
The space between the ignition sparker and the burner
must be clean.
The burners are wet. Dry the burner caps carefully.
The burner caps are not correctly positioned. Check that the burner caps are correctly positioned.
The appliance is not earthed, is poorly connected or the
earthing is faulty.
Contact the installation technician.
The burner flame is not uni-
form.
The burner components are not correctly positioned. Correctly place the parts on the appropriate burner.
The grooves on the burner are dirty. Clean the grooves on the burner.
The gas flow is not normal or
there is no gas.
The gas supply is blocked by gas taps. Open all gas taps.
If the gas is supplied from a gas cylinder, check that it is
not empty.
Change the gas cylinder.
The kitchen smells of gas. A gas tap has been left on. Turn off the taps.
Incorrect coupling of gas cylinder. Check that the coupling is sound.
Possible gas leak. Shut off the gas supply, ventilate the premises and imme-
diately notify an authorised installation technician to check
and certify the installation. Do not use the appliance until
ensuring that there is no gas leak in the installation or
appliance itself.
The burner immediately
switches off after releasing the
control knob.
The control knob was not held down for long enough. Once the burner is on, hold the control knob down a few
seconds longer.
The grooves on the burner are dirty. Clean the grooves on the burner.
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Siemens EP6A6PB80 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Siemens EP6A6PB80

Siemens EP6A6PB80 Bedienungsanleitung - Deutsch, Holländisch, Französisch, Italienisch - 44 seiten

Siemens EP6A6PB80 Bedienungsanleitung - Portugiesisch, Spanisch, Türkisch - 44 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info