Bedienungsanleitung Siemens RDF 210 (Seite 2 von 2) (Englisch)

485934

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Do you want to view the programmable timer settings?

CE1B3058en / 17.11.2005 Subject to alteration Building Technologies / HVAC Products

Do you want to reload the default timer settings?

Set the controller to standby .

2. Press and simultaneously for 3 seconds. Release them and, within 2

seconds, press 2 times

Day/s

Time when controller is in normal operation

Mo (1) – Fr (5) 06:30 – 08:30 (A1) 17:30 – 22:30 (A2)

Sa (6) 08:00 – 23:00 (A3)

Su (7) 08:00 – 22:30 (A4)

Default

settings

- in the remaining time controller is in energy saving

- timer A5…A8 are free, no default setting

Changing the control parameters

To optimize the control performance, a number of control parameters can be adjusted. This can

also be made during operation without opening the controller.

If you want to change the control parameters, proceed as follows:

(For factory settings, see table on the right-hand side)

1. Set the controller to standby

2. Press

and simultaneously for a minimum of 3 and a

maximum of 5 seconds. Release them and, within 2 seconds, press

the

again for 3 seconds. The display will show “P01”.

3. Select the required parameter by repeatedly pressing the

or button:

P01 P02 P22 P98

+-+

3057z03

P99

P25

4. Press

and simultaneously. The current value of the selected

parameter will appear, which can be changed by repeatedly pressing

or .

5. By pressing

and simultaneously again or 5 seconds.

after the last press of a button, the last parameter will be displayed

again.

6. If you wish to display and change additional parameters,

repeat steps 3 through 5.

7. 10 seconds after the last display or setting, all changes are

stored and the controller will return to standby.

8. Switch to normal operation with the button.

Recalibrating the sensor

If the room temperature displayed by the controller does not agree with the temperature effectively

measured, the temperature sensor can be recalibrated. For that purpose parameter P07 must be

changed.

Proceed as described under “Changing the control parameters” and follow steps

1 through 3 to select parameter P07.

With step 4, the room temperature displayed can now be matched to the

temperature effectively measured. Each push of the

or button changes

the temperature by + or – 0.5 °C up to a maximum of + / - 3 °C.

With step 7, the recalibration is automatically stored 10 seconds after the last

readjustment.

Commissioning (by qualified HVAC staff) (all temperature settings can be made in increments of 0.5 K)

Para-

meter

Controller’s parameter factory settings: Setting range RDF210 RDF210.2

P01 Setpoint of heating in energy saving mode (Wheat

Eco

) 16 OFF, 5 °C…Wcool

Eco

P02 Setpoint of cooling in energy saving mode (Wcool

Eco

) 28 OFF, Wheat

Eco

…40 °C

P03

Setpoint of heating in standby

(Wheat

Stb

)

OFF OFF, 5 °C…Wcool

Stb

P04

Setpoint of cooling in standby

(Wcool

Stb

)

OFF OFF, Wheat

Stb

…40 °C

P05 Minimum setpoint limitation in normal operation (Wmin

Norm

) 5 °C 5 °C…Wmax

Norm

P06 Maximum setpoint limitation in normal operation (Wmax

Norm

) 35 °C

Wmin

Norm

…40 °C

P07 Sensor calibration 0 K

-3…+3 K

P08 Switching differential heating SDH 2 K

0.5…+4K

P09 Switching differential cooling SDC 1 K

0.5…+4K

P10 Switching differential fan speed 2 in heating operation mode SDH2 1 K

0.5…+4K

P11 Switching differential fan speed 2 in cooling operation mode SDC2 1 K

0.5…+4K

P12 Switching differential fan speed 3 in heating operation mode SDH3 1 K

0.5…+4K

P13 Switching differential fan speed 3 in cooling operation mode SDC3 1 K

0.5…+4K

P14 Dwelling time of auto fan speeds 2 min.

1…5 minutes

P15 Minimum output on-time (Y11) 1 min.

1…10 minutes

P16 Minimum output off-time (Y11) 1 min.

1…10 minutes

P17 Selection of °C or °F °C °C or °F

P18 Display of temperature or setpoint ON

OFF: Setpoint

ON: Room (or return air)

temperature

P20 Fan control in energy saving mode OFF

OFF in dead zone

ON in dead zone

P21 Fan control in normal operation OFF

OFF in dead zone

ON in dead zone

P22 Heating / cooling mode

Cooling

only

0: Heating only

1: Cooling only

2: Automatic c/h changeover

P23 Heating / cooling changeover switching point cooling 16°C 10…25 °C

P24 Heating / cooling changeover switching point heating 28°C 27…40 °C

P25 Infrared receiver (only with RDF.../IR) 1

0: Disabled

1: Enabled

P98 Active temperature sensor

Diagnostic

value

0: Internal sensor

1: External sensor

P99

Value of current heating / cooling changeover temperature

reading or indication of current mode

Diagnostic

value

100 = input open Æ mode

0…49 °C = cur. temp. value

00 = input bridged Æ

mode

OFF= not commissioned as

automatic c/h changeover

Press the button to sequentially review the 8 auto timers.

Legend to table

Adjustable: Please record all changes you make

Not adjustable / display only

Not adjustable / no display

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RDF 210 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RDF 210

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info