Bedienungsanleitung Siemens RDG400KN (Seite 2 von 2) (Englisch)

555881

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Timer to extended presence or absence

The Comfort and Economy modes can be temporarily extended by 0.5 to 9.5 hours using the timer.

1. To set the timer, press and hold the operating mode button.

While holding the button, turn the rotary knob clockwise or counterclockwise as required.

a) Turn the rotary knob clockwise to extend Comfort mode.

Display:

0...+9:30

b) Turn the rotary knob counterclockwise to extend Economy mode.

Display:

0...–9:30

2. Release the operating mode button and the mode is temporarily changed, indicated by

symbol.

 After the temporary timer has elapsed, the thermostat will resume operation in the operating mode

according to schedule via bus (if available). Without schedule:

– when extended Comfort mode ends  new operating mode = Economy

– when extended Economy mode ends  new operating mode = Comfort

 If Economy mode cannot be selected via the operating mode button (P02 ≠ 2), Protection mode will

be used for extended absence instead.

 The temporary timer function is aborted whenever a new setting is made.

Temporary timer to extend the Comfort mode

When the operating mode is Economy (commanded by schedule via KNX or by en external signal. e.g.

keycard), it can be set back to Comfort temporarily by pressing the operating mode button.

The

symbol will appear.

Pressing the operating mode button again will stop the timer.

This function is only available when parameter P02 = 1. Duration: * P68 = 0...360 min, factory setting = 0 min.

* Needs to be configured by your HVAC installer.

Reminder clean filter and display of external faults

AL1 *

AL3 *

These fault messages tell you an external fault has occurred *:

AL1 : _______________________ AL3 : __________________________

* Needs to be configured by your HVAC installer

Button lock

 If the button lock function is enabled (parameter P14 = 2), then pressin

the

right button for 3 seconds

will lock or unlock the buttons respectivel

Locked buttons are indicated with the key symbol

 If "Auto lock" is confi

ured (P14 = 1), the thermostat will automaticall

lock the

buttons 10 seconds after the last adjustment.

Commissioning (by qualified HVAC installer)

To adapt the thermostat to

our s

stem and optimize the control performance, a number of control

parameters can be adjusted. This can be done during operation, either via the buttons on the thermo-

stat or via a commissioning tool.

Control parameters

If you wish to change control parameters, proceed as follows:

1. Press left and right buttons simultaneously for at least 3 seconds.

2. Release them and, within 2 seconds, press the right button again for 3 seconds.

The display will show P01.

3. Select the required parameter by turning the rotary knob.

4. Press button

(OK). The current value of the selected parameter starts blinkin

and can be chan

by turning the rotary knob.

5. Press button

(OK) to confirm the adjusted value, or (Esc) to cancel the change.

If you wish to adjust additional parameters, repeat steps 3 through 5, or press (Esc) to leave the

parameter setting mode.

Parameter list

No. Description Default value Setting range Adj. 

P01 Control sequence *** 1 = cooling only 0 = Heating only

1 = Cooling only

2 = H/C changeover, manual

3 = H/C changeover, automatic

P02 Mode selection via operating mode

button

1 = Auto** / Comfort / Protection

2 = Auto** / Comfort / Economy /

Protection

P04 Selection of °C or °F 0 = °C 0 = °C

1 = °F

P05 Sensor calibration 0.0 K -3...+3 °C

P06 Standard temperature display 0 = Room temp. 0 = Room temperature

1 = Setpoint

P07 Additional user information 0 = No display 0 = No display

1 = Room Temperature in °C / °F

2 = Outside temperature (via bus)

3 = Time of day (12h, via bus)

4 = Time of day (24h, via bus)

P08 Comfort basic setpoint 21 °C 5 ... 40 °C

P09 Minimum setpoint limitation in

Comfort mode

5 °C 5 ... 40 °C

P10 Maximum setpoint limitation in

Comfort mode

35 °C 5 ... 40 °C

P11 Setpoint for heating in Economy mode

(WheatEconomy)

15 °C OFF, 5 °C…WcoolEconomy

P12 Setpoint for cooling in Economy mode

(WcoolEconomy)

30 °C OFF, WheatEconomy…40 °C

P14 Button lock 0 = Disabled 0 = Disabled

1 = Automatic

2 = Manual

** When no time schedule via KNX exists, then Auto is equal to Comfort.

*** Not supported with all configurations.

All temperature settings can be made in increments of 0.5 °C.

 Please record all changes you make!

Siemens Building Technologies

Subject to change

CE1B3192en

12 May 2010

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RDG400KN Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RDG400KN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info