483779
5
Zoom out
Zoom in
Vorherige Seite
1/6
Nächste Seite
Siemens Building Technologies CE1N2222E / 14.01.1999
Landis & Staefa Division 5/6
The room temperature controller should be fitted in the main living room.
The place of installation should be chosen so that the sensor can capture the room
temperature as accurately as possible, without being affected by direct solar radia-
tion or other heating or cooling sources.
Mounting height is approx. 1.5 m above the floor.
The unit can be fitted to most commercially available recessed conduit boxes or di-
rectly on the wall.
When installing the room temperature controller, the base plate must first be fitted
and wired. Then, the unit is engaged at the top, swung downward and secured with a
screw.
For more detailed information, please refer to the installation instructions supplied
with the controller.
For the electrical installation, the local safety regulations and standards must be
complied with.
The remote operation contact T1 / T2 must be wired separately, using a separate
shielded cable.
The battery transit tab, which prevents inadvertent operation of the unit during trans-
port and storage, must be removed from the batteries.
The control characteristics can be changed with the help of the DIP switches located
at the rear of the unit. For detailed information, please refer to the commissioning in-
structions.
If the reference room is equipped with thermostatic radiator valves, they must be set
to their fully open position.
If the displayed room temperature does not agree with the measured room tem-
perature, the temperature detector should be recalibrated (please refer to
"Calibration of detector").
L
L1
Y1
M1
N1
AC 24...250 V
2222A01
N
L
L1
Y1
M1
N1
AC 24...250 V
2222A02
N
S1
T1 T2
REV11 REV11T
L Live, AC 24 ... 250 V S1 Remote operation unit (potential-
free)
L1 N.O. contact, AC 24 ... 250 V /
8 (3.5) A
T1 Signal "remote operation"
M1 Circulating pump T2 Signal "remote operation"
N1 REV11.. controller Y1 Regulating unit
Notes
Engineering
Fitting and installation
Commissioning
Connection dia-
grams
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Siemens REV 11 CHRONOGYR wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Siemens REV 11 CHRONOGYR

Siemens REV 11 CHRONOGYR Zusatzinformation - Holländisch - 2 seiten

Siemens REV 11 CHRONOGYR Bedienungsanleitung - Holländisch - 2 seiten

Siemens REV 11 CHRONOGYR Bedienungsanleitung - Französisch - 2 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info