Bedienungsanleitung Siemens REV-R.01-1 (Seite 10 von 12) (Englisch)

456799

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

10/12

Siemens Building Technologies Product-Data Sheet Radio signal unit REV... CE1N2255en

Landis & Staefa Division 16.10.2000

• When mounting the unit, the baseplate must first be fitted and wired (L/N = mains

230 V, LX/L1 = consumers). Then, it must be engaged at the top, swung downward

and secured with a screw

• For more detailed information, please refer to the Installation Instructions supplied

with the unit

For the electrical installation, the local regulations must be complied with.

Commissioning notes receiver REV-R.01/1

It is recommended to first commission and switch on the receiver, then the transmitter.

• Switch on mains supply

a) Press “Reset” button (= delete) for about 4 seconds, LED flashes briefly (delet-

ing the stored address)

b) Press “Set” button (= setting / learning) for about 3 seconds until the LED lights

c) The duration of the receiver’s learning readiness is a maximum of 25 minutes.

If no signal is received from the transmitter during that period of time, repeat

steps b) and c)

d) Mount transmitter and put it into operation

e) When the receiver receives a signal from the transmitter, the LED flashes briefly

f) When the LED is steady on, the relay is energized = controlled device ON

g) When the LED is dark, the relay is de-energized = controlled device OFF

h) In the event of a power failure at the receiver, the relay will automatically be

de-energized.

The transmitter repeats the ON or OFF signal at 20-minute intervals,

depending on the operational status. This means that the relay will be

energized / de-energized again after no more than 20 minutes. This interval

was selected to prolong battery life

If the REV-R.01/1 receives no signal from the controller / transmitter for 60 minutes, the

relay will drop out so that the controlled device will automatically be switched off.

Commissioning notes controller / transmitter REV22RF

It is recommended to first commission and switch on the receiver and then the trans-

mitter.

• If the reference room is equipped with thermostatic radiator valves, they must be fully

opened

• The control mode can be changed with a DIP switch at the rear of the unit

• The battery transit tab, which prevents inadvertent operation of the unit during trans-

port and storage, must be removed from the batteries. The unit switches on

a) When – immediately after switching on – symbol

(controlled device ON)

appears on the display, the first signal has already been transmitted to the

receiver and communication has been opened

b) Make settings in agreement with the Operating Instructions

c) If symbol

(controlled device ON) does not appear on the display, it

must first be activated for signal transmission

d) Set operating mode selector to position

e) Set setting slider to

f) Press - /+ buttons to adjust the setpoint to 29 °C

g) Symbol

(heating ON) appears on the display after a maximum of one

minute

h) The first signal transmission to the receiver has been completed

i) After 10 seconds, the transmitter sends another signal

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens REV-R.01-1 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens REV-R.01-1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info