Bedienungsanleitung Siemens REV23M (Seite 5 von 16) (Deutsch, Englisch, Holländisch, Französisch)

41499

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

CE1G2266xx 03.07.2003 5/16

Press to accept. (factory setting) will flash. Press to

accept or continue rolling toward the display to select one

of the following control modes:

, PID 6, PID 12 or . Press to accept the

required control mode.

A brief description of the control modes is given below

(also refer to Fig.

Permanent self-learning adaptive control:

Suited for all standard applications (factory

setting).

PID 12 Normal controlled systems:

For locations with normal temperature variations.

PID 6 Fast controlled systems:

For locations with significant temperature

variations.

Difficult controlled systems:

Proper on / off controller with a switching

differential of 0.5 C.

4.2.5 Frost protection mode

Use operating mode selector to select symbol (also

refer to Fig.

). If the standard value of 5 °C need to be

changed, the frost protection setpoint

must be

changed via temperature menu T (refer to the Operating

Instructions).

5 Replace the controller

Proceed according to Fig. G.

6 Functional check

a) 60 seconds after the batteries supply power, an error

message

must appear

b) Switch on the boiler

c) The error message must disappear after 2 minutes at

the latest

d) Comfort mode

e) Select temperature menu T and adjust the temperature

setpoint

to 29 °C (refer to the Operating

Instructions)

f) Symbol

must appear on the display after

3 minutes at the latest. If that is not the case:

• Check the boiler

• The room temperature is possibly above 29 °C

g) Reset the setpoint temperature

to the initial value

(standard value 19 °C or individual setting)

h) Select the required operating mode

7 Reset

User-defined data:

Press the button behind the pin opening for at least

one second: This resets the userspecific settings and the

“Permanent-self-learning operating mode” as well as

display of flow temperature, outside temperature and

d.h.w. setpoint to their default values (the heating engineer

settings will not be changed). The clock starts at 12:00.

During the reset time, all sections of the display light up,

enabling them to be checked.

All user-defined data plus the heating engineer

settings:

Press the button behind the pin opening together with the

warmer and colder buttons for at least one second.

After this reset, the factory settings will be reloaded (also

refer to section “Factory settings“ in the Operating

Instructions).

Caution: If the controller is removed from its base for

more than 30 seconds, an error message will

appear on the display.

When sliding the controller back to its base,

the error message must disappear after

2 minutes at the latest.

Without inserted batteries, reset functions

correctly for a maximum of 15 seconds only

after removing REV23M from its base.

8 Notes

• REV23M is an electric weekly programmable room

temperature controller.

• The controller conforms to “Software Class A” and is for

use in “normal” pollution situations.

• If the reference room is equipped with thermostatic

radiator valves, they must be set to their fully open

position.

• Remote operation contact T1 / T2 must be wired

separately using a separate shielded cable.

• Ensure that the local regulations for electrical

installations are complied with.

• REV23M can only be used in connection with an

OpenTherm Plus-compatible boiler.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens REV23M Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens REV23M

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info