Bedienungsanleitung Siemens RVP210 (Seite 6 von 8) (Englisch)

555849

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

CE2N2462E / 09.12.1998 Siemens Building Technologies

6/8 Landis & Staefa Division

When connecting an external switching contact to the controller's terminals A6-MD, the

operating mode can be selected from a remote location:

–

Contact closed: controller is in standby mode

–

Contact open: controller uses the operating mode selected with the slider

–

The wires of the measuring circuits carry extra low voltage

–

The wires to the actuator and the pump carry AC 24...230 V

–

The local electrical regulations must be complied with

–

Detector cables must not be run parallel to mains carrying cable for loads such as

actuator, pump, burner, etc. (safety class II to EN 60730)

–

The maximum limitation of the boiler temperature may not be used as a safety function.

For that purpose a thermostat or safety limiter must be connected at terminals L-F1/F4

Setpoint adjustments:

–

Normal temperature (in °C room temperature)

–

Setback (in °C room temperature)

–

D.h.w. (only with the RVP210)

Settings to be made by the heating engineer:

–

Slope of heating curve

–

Authority of room temperature

–

ECO heating limit

–

Maximum limitation of the flow or boiler temperature

–

Type of regulating unit (mixing valve or burner)

–

Type of control (three- or two-position)

–

Frost protection activated or deactivated

–

Priority of d.h.w. heating (only with the RVP210)

The controller is supplied complete with installation instructions and operating instruc-

tions.

- conformance to

EMC directive 89/336/ EEC

Immunity EN 50082-2

Emissions EN 50081-1

Low voltage directive 73/23/ EEC

Safety EN 60730-1

Rated operating voltage AC 230 V ±10 %

Frequency 50 Hz

Power consumption 7 VA

Degree of protection (cover closed) IP40 D EN 60529

Safety class II EN 60730

Permissible ambient temperatures

Transport –25...+70 °C

Storage –5...+55 °C

Operation 0...50 °C

Weight (net) 0.72 kg

Test class II

Rated voltage AC 230 V

Rated current 2 (2) A

Contact current at AC 24...90 V 0.1...2 A, cos ϕ >0.5

Contact current at AC 90...250 V 0.02...2 A, cos ϕ >0.5

Rated current of ignition transformer 1 A max.(30 s max.)

Switch-on current of ignition transformer 10 A max.(10 ms max.)

Setpoint of normal room temperature 20 ±0...8 °C

Setback for reduced room temperature –12...0 K

Setpoint of d.h.w. temperature (only with the RVP210) 10...60 °C

Slope of heating curve 0.25...4

Max. limit of flow or boiler temperature 8...100 °C

ECO heating limit –10...+8 °C (referred to normal setpoint)

Authority of room temperature 0...100 %

Switching differential with two-position control 1...20 K

Analog time switches 12 hours

Digital weekly time switch with backup battery

Switching contact

Notes

Engineering

Commissioning

Technical data

General data

Output relays

Setting ranges

Backup of time switches

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RVP210 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info